NTP needs some time so sync with other servers (even when using burst option). If your stratum is too low (16 = not synchronized) clients will refuse to take time from the server. How long have you waited? What does
Hi.
i was wondering if anyone can show me or direct me on setting up a ntp server under redhat.. Is there any howtos so i can get familar to it "any good sites" (3 Replies)
All,
How do you set a Solaris 9 server which received ntp updates from a ntp server to broadcast them on a local subnet. I have created a /etc/inet/ntp.conf file to receive the updates from a server on network and need to make this server become like a ntp relay from the main server.
Any... (1 Reply)
Hello Guys,
i have a problem my local server is not getting synchronized with ntpd server.
1)ntpq -p is giving the following output
remote refid st t when poll reach delay offset jitter
==============================================================================
... (9 Replies)
Hi All....
I need to configure NTP server in my network, which is heterogeneous, containing Linux as well as windows systems. I'm planning to configure it on RHEL 5.0. What are the prerequisites for this and do I need to register this server?
Can anyone give me as many information as... (1 Reply)
All here, thank you for listening. Now I've set up a Linux NTP server by adding a external windows NTP server in /etc/ntp.conf. Then I start the ntpd daemon. But how often does the Linux NTP server update its time with the external NTP server? I've looked up everywhere but found no information... (1 Reply)
hello Guys,
I have an NTP problem on my SUN N240 server. External NTP server is being used for this box and when i run 'ntpq -p' i get connection refused message;
Code:
ntpq -p ntpq: read: Connection refused
Here this is the ntp.conf file:
Code:
cat /etc/ntp.conf # BEGIN NTP... (1 Reply)
Hi,
I have two ntp servers in my cluster and I want all the nodes in my cluster to sync with either of the ntp servers or just one. Unfortunately it keep rotating the sync, between my ntp server 1, ntp server 2 and local. Is there anyway I can change the sync to avoid local?
# ntpq -p
... (3 Replies)
Hello
I need to create NTP server for all my devices, What is the best OS for NTP Server? "CentOS, Redhat, Ubuntu "
I tried before Ubuntu but some of device not detect the server
Need your recommendation
Thank you (2 Replies)
Discussion started by: moudmm
2 Replies
LEARN ABOUT REDHAT
ntptrace
ntptrace(1) User Commands ntptrace(1)NAME
ntptrace - Trace peers of an NTP server
SYNOPSIS
ntptrace [-flags] [-flag [value]] [--option-name[[=| ]value]] [host]
DESCRIPTION
ntptrace is a perl script that uses the ntpq utility program to follow the chain of NTP servers from a given host back to the primary time
source. For ntptrace to work properly, each of these servers must implement the NTP Control and Monitoring Protocol specified in RFC 1305
and enable NTP Mode 6 packets.
If given no arguments, ntptrace starts with localhost. Here is an example of the output from ntptrace:
% ntptrace localhost: stratum 4, offset 0.0019529, synch distance 0.144135
server2ozo.com: stratum 2, offset 0.0124263, synch distance 0.115784 usndh.edu:
stratum 1, offset 0.0019298, synch distance 0.011993, refid 'WWVB'
On each line, the fields are (left to right): the host name, the host stratum, the time offset between that host and the local host (as
measured by ntptrace; this is why it is not always zero for "localhost"), the host synchronization distance, and (only for stratum-1
servers) the reference clock ID. All times are given in seconds. Note that the stratum is the server hop count to the primary source, while
the synchronization distance is the estimated error relative to the primary source. These terms are precisely defined in RFC-1305.
OPTIONS -n, --numeric
Print IP addresses instead of hostnames.
Output hosts as dotted-quad numeric format rather than converting to the canonical host names.
-m number, --max-hosts=number
Maximum number of peers to trace. This option takes an integer number as its argument. The default number for this option is:
99
This option has not been fully documented.
-r string, --host=string
Single remote host. The default string for this option is:
127.0.0.1
This option has not been fully documented.
-?, --help
Display usage information and exit.
-!, --more-help
Pass the extended usage information through a pager.
-v [{v|c|n --version [{v|c|n}]}]
Output version of program and exit. The default mode is `v', a simple version. The `c' mode will print copyright information and
`n' will print the full copyright notice.
EXIT STATUS
One of the following exit values will be returned:
0 (EXIT_SUCCESS)
Successful program execution.
1 (EXIT_FAILURE)
The operation failed or the command syntax was not valid.
70 (EX_SOFTWARE)
libopts had an internal operational error. Please report it to autogen-users@lists.sourceforge.net. Thank you.
NOTES
This manual page was AutoGen-erated from the ntptrace option definitions.
ntp (4.2.8p13) 20 Feb 2019 ntptrace(1)