10-15-2008
Sorry, not sure I'm clear. Did you remove it completely, or try setting it to this (or both):
timeserver=localhost
You're timezone is mis-spelled. Was that a cut-n-paste?
10 More Discussions You Might Find Interesting
1. Solaris
We are installing Solaris 9 with Jumpstart ...facing problems..
Problem is .it is prompting for questions, even though we set the Sysidcfg and class files properly.
when we give "boot net - install" at OK prompt, it is coming till
"The system is coming up. Please wait"
After that it... (5 Replies)
Discussion started by: b_manu78
5 Replies
2. Solaris
I am trying to install Solaris 10 OS using jumpstart over WAN. I have configured the jumpstart server with apache server and created all the necessary configurations and files. When i WAN boot my target machine, it gets booted using wanboot, it downloads the miniroot from the jumpstart server, but... (3 Replies)
Discussion started by: hemalsid
3 Replies
3. Solaris
I am trying to install Solaris 10 on a target machine which is t1000. ( sun4v). I have configured my jumpstart server to install solaris over WAN. when i boot my machine, the wanboot image gets downloaded properly, miniroot gets downloaded properly, but after that the process fails with the... (3 Replies)
Discussion started by: hemalsid
3 Replies
4. Solaris
I get following error while doing a flash installation. I 'm trying to deploy a flash archive created by our engineering team. I 'm trying to install it with ZFS root and the profile which i using is as following
#more flash_profile_test
install_type flash_install
archive_location nfs... (3 Replies)
Discussion started by: fugitive
3 Replies
5. Solaris
hi friends,
i dont know how to install jumpstart . i have solaris cds( 5 nos.). i tried to install jumpstart but there is no setup_install_server file. What i want to do for installing jumpstart server
please help me
thanks to all (8 Replies)
Discussion started by: sijocg
8 Replies
6. Solaris
I am trying to install Solaris x86 using the Jumpstart server. I run the add_install_client command with appropriate options, and reboot my x86 Target box. The installation starts fine and unattended. After the installation completes and the target goes for a re-boot, it does not boot from the HDD... (9 Replies)
Discussion started by: hemalsid
9 Replies
7. Solaris
hello
I created a boot server and tryed to run intstall with jumpstart on other solaris server, but jumpstart coudn't starts, only text-based install. sysidcfg and rules file are in the same shared folder, rules file has only one string
any - - any_profile - and thta't all. also I created... (2 Replies)
Discussion started by: sluge
2 Replies
8. Solaris
Hi
actualy my two machines are sun sparc ultra 60. Both are same configuration. I am trying jumpstart Installation in my two machines, i got no errors in server side but in the client side actually it detects the server machine with correct hostname and domainname but after showed that it will... (2 Replies)
Discussion started by: Grovestreet
2 Replies
9. Solaris
Not very helpful to say the least. Seems to read the flar file and go through the upgrade and then come up with this error.
Any ideas? (1 Reply)
Discussion started by: psychocandy
1 Replies
10. Solaris
I am trying to configuring jumpstart configuration. Please find below sysidcfg configuration file output
bash-3.2# cat sysidcfg
terminal=vt100
network_interface=nxge0 { primary hostname=sun1 ip_address=192.168.11.10 \
protocol_ipv6=no netmask=255.255.255.0 default_route=192.168.11.7}... (5 Replies)
Discussion started by: sb200
5 Replies
LEARN ABOUT DEBIAN
poe::component::ikc::specifier
IKC::Specifier(3pm) User Contributed Perl Documentation IKC::Specifier(3pm)
NAME
POE::Component::IKC::Specifier - IKC event specifer
SYNOPSIS
use POE;
use POE::Component::IKC::Specifier;
$state=specifier_parse('poe://*/timeserver/connect');
print 'The foreign state is '.specifier_name($state);
DESCRIPTION
This is a helper module that encapsulates POE IKC specifiers. An IKC specifier is a way of designating either a kernel, a session or a
state within a IKC cluster.
IKC specifiers have the folloing format :
poe:://kernel/session/state
kernel may a kernel name, a kernel ID, blank (for local kernel), a '*' (all known foreign kernels) or host:port (not currently supported).
session may be any session alias that has been published by the foreign kernel.
state is a state that has been published by a foreign session.
Examples :
"poe://Pulse/timeserver/connect"
State 'connect' in session 'timeserver' on kernel 'Pulse'.
"poe:/timeserver/connect"
State 'connect' in session 'timeserver' on the local kernel.
"poe://*/timeserver/connect"
State 'connect' in session 'timeserver' on any known foreign kernel.
"poe://Billy/bob/"
Session 'bob' on foreign kernel 'Billy'.
EXPORTED FUNCTIONS
"specifier_parse($spec)"
Turn a specifier into the internal representation (hash ref). Returns undef() if the specifier wasn't valid.
print Dumper specifer_parse('poe://Pulse/timeserver/time');
would print
$VAR1 = {
kernel => 'Pulse',
session => 'timeserver',
state => 'time',
};
Note : the internal representation might very well change some day.
"specifier_name($spec)"
Turns a specifier into a string.
BUGS
AUTHOR
Philip Gwyn, <perl-ikc at pied.nu>
COPYRIGHT AND LICENSE
Copyright 1999-2011 by Philip Gwyn. All rights reserved.
This library is free software; you can redistribute it and/or modify it under the same terms as Perl itself.
See <http://www.perl.com/language/misc/Artistic.html>
SEE ALSO
POE, POE::Component::IKC::Responder
perl v5.12.4 2011-08-27 IKC::Specifier(3pm)