10-14-2008
Jumpstart Solaris Installation Program screen
Hi!
I'm trying to skip the installation welcome screen (actually the first three screens: The Solaris Installation Program screen, Identify This System screen and date and time settings - not timezone settings). Everything else runs automaticly from jumpstart except these three screens, just need to get rid of there three f2 key presses.
Any help is kindly appreciated.
Regards, Luka
10 More Discussions You Might Find Interesting
1. Solaris
We are installing Solaris 9 with Jumpstart ...facing problems..
Problem is .it is prompting for questions, even though we set the Sysidcfg and class files properly.
when we give "boot net - install" at OK prompt, it is coming till
"The system is coming up. Please wait"
After that it... (5 Replies)
Discussion started by: b_manu78
5 Replies
2. Solaris
I am trying to install Solaris 10 OS using jumpstart over WAN. I have configured the jumpstart server with apache server and created all the necessary configurations and files. When i WAN boot my target machine, it gets booted using wanboot, it downloads the miniroot from the jumpstart server, but... (3 Replies)
Discussion started by: hemalsid
3 Replies
3. Solaris
I am trying to install Solaris 10 on a target machine which is t1000. ( sun4v). I have configured my jumpstart server to install solaris over WAN. when i boot my machine, the wanboot image gets downloaded properly, miniroot gets downloaded properly, but after that the process fails with the... (3 Replies)
Discussion started by: hemalsid
3 Replies
4. Solaris
I get following error while doing a flash installation. I 'm trying to deploy a flash archive created by our engineering team. I 'm trying to install it with ZFS root and the profile which i using is as following
#more flash_profile_test
install_type flash_install
archive_location nfs... (3 Replies)
Discussion started by: fugitive
3 Replies
5. Solaris
hi friends,
i dont know how to install jumpstart . i have solaris cds( 5 nos.). i tried to install jumpstart but there is no setup_install_server file. What i want to do for installing jumpstart server
please help me
thanks to all (8 Replies)
Discussion started by: sijocg
8 Replies
6. Solaris
I am trying to install Solaris x86 using the Jumpstart server. I run the add_install_client command with appropriate options, and reboot my x86 Target box. The installation starts fine and unattended. After the installation completes and the target goes for a re-boot, it does not boot from the HDD... (9 Replies)
Discussion started by: hemalsid
9 Replies
7. Solaris
hello
I created a boot server and tryed to run intstall with jumpstart on other solaris server, but jumpstart coudn't starts, only text-based install. sysidcfg and rules file are in the same shared folder, rules file has only one string
any - - any_profile - and thta't all. also I created... (2 Replies)
Discussion started by: sluge
2 Replies
8. Solaris
Hi
actualy my two machines are sun sparc ultra 60. Both are same configuration. I am trying jumpstart Installation in my two machines, i got no errors in server side but in the client side actually it detects the server machine with correct hostname and domainname but after showed that it will... (2 Replies)
Discussion started by: Grovestreet
2 Replies
9. Solaris
Not very helpful to say the least. Seems to read the flar file and go through the upgrade and then come up with this error.
Any ideas? (1 Reply)
Discussion started by: psychocandy
1 Replies
10. Solaris
I am trying to configuring jumpstart configuration. Please find below sysidcfg configuration file output
bash-3.2# cat sysidcfg
terminal=vt100
network_interface=nxge0 { primary hostname=sun1 ip_address=192.168.11.10 \
protocol_ipv6=no netmask=255.255.255.0 default_route=192.168.11.7}... (5 Replies)
Discussion started by: sb200
5 Replies
LEARN ABOUT MOJAVE
dmxgetscreencount
DMXGetScreenCount(3) Library Functions Manual DMXGetScreenCount(3)
NAME
DMXGetScreenCount - determine number of back-end screens
SYNOPSIS
#include <X11/extensions/dmxext.h>
Bool DMXGetScreenCount(Display *dpy,
int *screen_count);
DESCRIPTION
DMXGetScreenCount() returns the number of back-end screens that a Xdmx(1) server controls. Since a DMX screen usually fills all of the
available area on a back-end server, there is usually a one-to-one correspondence between DMX screens and backend servers. However, it is
also possible for a DMX screen to cover only part of the available area on a back-end server, and for more than one DMX screens to occupy
different parts of the visible area on the same back-end server.
A DMX screen may be managed as a regular X screen in the Xdmx(1) server or may be joined with other DMX screens using Xinerama.
RETURN VALUE
DMXGetScreenCount() sets screen_count and returns True unless there is a protocol error.
NOTES
If Xinerama is active, only one logical screen will be available to clients of the Xdmx(1) server. However, this call will accurately
reflect the number of composite back-end screens that the Xdmx(1) server is using.
SEE ALSO
DMXGetScreenAttributes(3), DMXChangeScreensAttributes(3), DMX(3), Xdmx(1)
X Version 11 libdmx 1.1.2 DMXGetScreenCount(3)