and
after you get the package names with the last command check the versions of cluster software with:
maybe there is an older version of cluster installed or maybe it is only partial installed (the first command will check for this...).
greets,
DN2
Hi DN2,
Thank you very much for your prompt reply. I have followed above commands and found that "SUNWscman" package was installed and it was having 3.2.0,REV=2006.09.26.13.45 as VERSION. I have removed that package and now installing again.
Can you guide me what all things needs to be taken care before moving ahead with configuration with "scinstall" ?
Hi,
I have a Redhat Cluster Suite with 2 nodes, using option "Multicast HeartBeating" on clumembd, whith default IP: 225.0.0.11
The cluster member names are:
# grep node /etc/hosts
192.168.100.1 node1
192.168.100.2 node2
My problem is that the Multicast IP is relating to other network... (1 Reply)
Hi
I'm completely new to Solaris Disk Suite. Where can I go and read up about it. I've seen consultants run the meta- commands, but it doesn't make any sense to me. I would like to learn how it works and how to use it.
Thanks (1 Reply)
I am new to Solaris so please bear with me. I have spent enough time searching to get somewhat of a grip here but I am not sure what to do next. I am trying to grow a file system on a Solaris 8 server.
B_root@server:>df -k
Filesystem kbytes used avail capacity Mounted on... (9 Replies)
Hi,
is it normal, that the IP alias (service IP) can't be seen with ifconfig -a , as eth0:1 for example
the IP is on the node, you can ping it, and open ports for that IP
look at this:
# ip addr
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue
link/loopback... (4 Replies)
HI
How can i configure fence_cisco_ucs with redhat cluster suite.
i was trying to configure fencing aganet with red ahat cluster suite
i issued command
# /usr/sbin/fence_vmware_soap -a 172.22.90.61 -l admin -p duc2Cisco -o reboot
then i got below error:
Failed: You have to... (0 Replies)
Discussion started by: bentech4u
0 Replies
LEARN ABOUT SUNOS
clinfo
clinfo(1M) System Administration Commands clinfo(1M)NAME
clinfo - display cluster information
SYNOPSIS
clinfo [-nh]
DESCRIPTION
The clinfo command displays cluster configuration information about the node from which the command is executed.
Without arguments, clinfo returns an exit status of 0 if the node is configured and booted as part of a cluster. Otherwise, clinfo returns
an exit status of 1.
OPTIONS
The following options are supported:
-h Displays the highest node number allowed to be configured. This is different from the maximum number of nodes supported in a given
cluster. The current highest configured node number can change immediately after the command returns since new nodes can be dynam-
ically added to a running cluster.
For example, clinfo -h might return 64, meaning that the highest number you can use to identify a node is 64. See the Sun Cluster
3.0 System Administration Guide for a description of utilities you can use to determine the number of nodes in a cluster.
-n Prints the number of the node from which clinfo is executed.
EXIT STATUS
The following exit values are returned:
0 Successful completion.
1 An error occurred.
This is usually because the node is not configured or booted as part of a cluster.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcsu |
+-----------------------------+-----------------------------+
SEE ALSO attributes(5)SunOS 5.10 12 Mar 2002 clinfo(1M)