Hi,
I have a Redhat Cluster Suite with 2 nodes, using option "Multicast HeartBeating" on clumembd, whith default IP: 225.0.0.11
The cluster member names are:
# grep node /etc/hosts
192.168.100.1 node1
192.168.100.2 node2
My problem is that the Multicast IP is relating to other network... (1 Reply)
Hi
I'm completely new to Solaris Disk Suite. Where can I go and read up about it. I've seen consultants run the meta- commands, but it doesn't make any sense to me. I would like to learn how it works and how to use it.
Thanks (1 Reply)
I am new to Solaris so please bear with me. I have spent enough time searching to get somewhat of a grip here but I am not sure what to do next. I am trying to grow a file system on a Solaris 8 server.
B_root@server:>df -k
Filesystem kbytes used avail capacity Mounted on... (9 Replies)
Hi,
is it normal, that the IP alias (service IP) can't be seen with ifconfig -a , as eth0:1 for example
the IP is on the node, you can ping it, and open ports for that IP
look at this:
# ip addr
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue
link/loopback... (4 Replies)
HI
How can i configure fence_cisco_ucs with redhat cluster suite.
i was trying to configure fencing aganet with red ahat cluster suite
i issued command
# /usr/sbin/fence_vmware_soap -a 172.22.90.61 -l admin -p duc2Cisco -o reboot
then i got below error:
Failed: You have to... (0 Replies)
Discussion started by: bentech4u
0 Replies
LEARN ABOUT MOJAVE
locale::codes::langext5.18
Locale::Codes::LangExt(3pm) Perl Programmers Reference Guide Locale::Codes::LangExt(3pm)NAME
Locale::Codes::LangExt - standard codes for language extension identification
SYNOPSIS
use Locale::Codes::LangExt;
$lext = code2langext('acm'); # $lext gets 'Mesopotamian Arabic'
$code = langext2code('Mesopotamian Arabic'); # $code gets 'acm'
@codes = all_langext_codes();
@names = all_langext_names();
DESCRIPTION
The "Locale::Codes::LangExt" module provides access to standard codes used for identifying language extensions, such as those as defined in
the IANA language registry.
Most of the routines take an optional additional argument which specifies the code set to use. If not specified, the default IANA language
registry codes will be used.
SUPPORTED CODE SETS
There are several different code sets you can use for identifying language extensions. A code set may be specified using either a name, or
a constant that is automatically exported by this module.
For example, the two are equivalent:
$lext = code2langext('acm','alpha');
$lext = code2langext('acm',LOCALE_LANGEXT_ALPHA);
The codesets currently supported are:
alpha
This is the set of three-letter (lowercase) codes from the IANA language registry, such as 'acm' for Mesopotamian Arabic.
This is the default code set.
ROUTINES
code2langext ( CODE [,CODESET] )
langext2code ( NAME [,CODESET] )
langext_code2code ( CODE ,CODESET ,CODESET2 )
all_langext_codes ( [CODESET] )
all_langext_names ( [CODESET] )
Locale::Codes::LangExt::rename_langext ( CODE ,NEW_NAME [,CODESET] )
Locale::Codes::LangExt::add_langext ( CODE ,NAME [,CODESET] )
Locale::Codes::LangExt::delete_langext ( CODE [,CODESET] )
Locale::Codes::LangExt::add_langext_alias ( NAME ,NEW_NAME )
Locale::Codes::LangExt::delete_langext_alias ( NAME )
Locale::Codes::LangExt::rename_langext_code ( CODE ,NEW_CODE [,CODESET] )
Locale::Codes::LangExt::add_langext_code_alias ( CODE ,NEW_CODE [,CODESET] )
Locale::Codes::LangExt::delete_langext_code_alias ( CODE [,CODESET] )
These routines are all documented in the Locale::Codes::API man page.
SEE ALSO
Locale::Codes
The Locale-Codes distribution.
Locale::Codes::API
The list of functions supported by this module.
http://www.iana.org/assignments/language-subtag-registry
The IANA language subtag registry.
AUTHOR
See Locale::Codes for full author history.
Currently maintained by Sullivan Beck (sbeck@cpan.org).
COPYRIGHT
Copyright (c) 2011-2013 Sullivan Beck
This module is free software; you can redistribute it and/or modify it under the same terms as Perl itself.
perl v5.18.2 2013-11-04 Locale::Codes::LangExt(3pm)