10-13-2008
Solaris 10 - Cluster Suite 3.2 2/08 prob
Hi,
I am relatively new to Sun Solaris. I am installing 2 node cluster and when I was installing cluster suite 3.2 2/08, it is giving me this error as "Conflict - Incomplete version detected".
Please help me in this regard and also suggest me any valuable point to consider before going ahead with installation and configuration with scinstall utility.
Image -
http://www.2and2.net/files/48f356433896f.jpg
Thanks
Hitarth
8 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Does anyone know which packages I need to install to run Disk Suite on Solaris 7, or where I can find some documentation? (2 Replies)
Discussion started by: 98_1LE
2 Replies
2. Linux
Hi,
I have a Redhat Cluster Suite with 2 nodes, using option "Multicast HeartBeating" on clumembd, whith default IP: 225.0.0.11
The cluster member names are:
# grep node /etc/hosts
192.168.100.1 node1
192.168.100.2 node2
My problem is that the Multicast IP is relating to other network... (1 Reply)
Discussion started by: Livio
1 Replies
3. Solaris
Hi
I'm completely new to Solaris Disk Suite. Where can I go and read up about it. I've seen consultants run the meta- commands, but it doesn't make any sense to me. I would like to learn how it works and how to use it.
Thanks (1 Reply)
Discussion started by: soliberus
1 Replies
4. Solaris
I am new to Solaris so please bear with me. I have spent enough time searching to get somewhat of a grip here but I am not sure what to do next. I am trying to grow a file system on a Solaris 8 server.
B_root@server:>df -k
Filesystem kbytes used avail capacity Mounted on... (9 Replies)
Discussion started by: NewSolarisAdmin
9 Replies
5. High Performance Computing
Provides a description of how to set up a Solaris Cluster Express cluster in a VirtualBox on OpenSolaris.
More... (0 Replies)
Discussion started by: Linux Bot
0 Replies
6. Solaris
Pls tell me how can i recover adeleted user in solaris 8. Please help me I'm a newby thanks
aamer (4 Replies)
Discussion started by: aamer
4 Replies
7. Red Hat
Hi,
is it normal, that the IP alias (service IP) can't be seen with ifconfig -a , as eth0:1 for example
the IP is on the node, you can ping it, and open ports for that IP
look at this:
# ip addr
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue
link/loopback... (4 Replies)
Discussion started by: funksen
4 Replies
8. Red Hat
HI
How can i configure fence_cisco_ucs with redhat cluster suite.
i was trying to configure fencing aganet with red ahat cluster suite
i issued command
# /usr/sbin/fence_vmware_soap -a 172.22.90.61 -l admin -p duc2Cisco -o reboot
then i got below error:
Failed: You have to... (0 Replies)
Discussion started by: bentech4u
0 Replies
LEARN ABOUT CENTOS
cluster
CLUSTER(1) General Commands Manual CLUSTER(1)
NAME
cluster - find clusters in a graph and augment the graph with this information.
SYNOPSIS
cluster [-v?] [ -Ck ] [ -ck ] [ -o outfile ] [ files ]
DESCRIPTION
cluster takes as input a graph in DOT format, finds node clusters and augments the graph with this information. The clusters are specified
by the "cluster" attribute attached to nodes; cluster values are non-negative integers. cluster attempts to maximize the modularity of the
clustering. If the edge attribute "weight" is defined, this will be used in computing the clustering.
OPTIONS
The following options are supported:
-Ck specifies a targeted number of clusters that should be generated. The specified number k is only a suggestion and may not be real-
isable. If k == 0, the default, the number of clusters that approximately optimizes the modularity is returned.
-ck specifies clustering method. If k == 0, the default, the modularity will be used. If k == 1 modularity quality will be used.
-ooutfile
Specifies that output should go into the file outfile. By default, stdout is used.
-v Verbose mode.
EXAMPLES
Applying cluster to the following graph,
graph {
1--2 [weight=10.]
2--3 [weight=1]
3--4 [weight=10.]
4--5 [weight=10]
5--6 [weight=10]
3--6 [weight=0.1]
4--6 [weight=10.]
}
gives
graph {
node [cluster="-1"];
1 [cluster=1];
2 [cluster=1];
3 [cluster=2];
4 [cluster=2];
5 [cluster=2];
6 [cluster=2];
1 -- 2 [weight="10."];
2 -- 3 [weight=1];
3 -- 4 [weight="10."];
4 -- 5 [weight=10];
5 -- 6 [weight=10];
3 -- 6 [weight="0.1"];
4 -- 6 [weight="10."];
}
AUTHOR
Yifan Hu <yifanhu@research.att.com>
SEE ALSO
gvmap(1)
Blondel, V.D., Guillaume, J.L., Lambiotte, R., Lefebvre, E.: Fast unfolding of communities in large networks. Journal of Statistical
Mechanics: Theory and Experiment (2008), P10008.
3 March 2011 CLUSTER(1)