10-07-2008
That sounds like a good idea, but since I am looking to automate this, how could I determine when the appropriate time to remove it from dhcp is? I am developing an application that drives this so I wouldn't be able to put a specific time limit (as we know it can vary from system to system), what I need is some trigger or event that indicates the client has successfully finished the boot process. Any thoughts?
10 More Discussions You Might Find Interesting
1. Solaris
Hi
I just configured a jumpstart server for x86 and sparc clients. I don't use a dhcp server, so I configured /etc/ethers and did add_install_client to update /etc/bootparams. The sparc installation ist working, but the x86 installation stops after CD1 was successfully installed.
What I did:
I... (2 Replies)
Discussion started by: Jay_Fisi
2 Replies
2. Solaris
I need a little help figuring out why my custom jumpstart network installation is dumping me to a manual install.
I am trying to install Solaris 10 (unattended) over the wire from my jumpstart server to an HP Proliant DL380 server but I'm having difficulties with the unattended part.
So, what... (2 Replies)
Discussion started by: alias.256
2 Replies
3. Solaris
Does anyone know how to Jumpstart a Solaris 10 x86 system without the GUI?
I would like to keep the Jumpstart and/or Flash Archive install in a console text mode if possible but I've not had much luck finding instructions. I'm guessing this is going to be accomplished from the grub menu with a... (5 Replies)
Discussion started by: alias.256
5 Replies
4. Solaris
Can I use a Jumpstart enviroment on x86 to install a sparc64 client?
The idea is to install Solaris in an virtual environment (Sun Virtual Box) running on a pc (AMD), configure a Jumpstart server, and have a SUN Ultra 60 (sparc64) installed via the Jumpstart server.
The SUN has no cdrom... (4 Replies)
Discussion started by: eldiablo
4 Replies
5. Solaris
Hi All,
Is there a possible way to fully automate Solaris x86 jumpstart or make the x86 jumpstart unattended?
I'm currently checking the possible options on how can I do the x86 jumpstart to be kicked off during midnight.
We have an automated jumpstart (start to run from midnight) for... (2 Replies)
Discussion started by: racbern
2 Replies
6. Solaris
Hi friends ,
i have on ultra 10 Sparc machine . Due to some problem my OS is fully corrupted , so i am planning to install again but my problem is the cd drive in Ultra 10 machine is not working.
Now i am planning to use Jumpstart installation method to install my server.
But i... (4 Replies)
Discussion started by: vr_mari
4 Replies
7. Solaris
client boots fine, it gets the ip 192.168.0.10 and the bootfile. Then there is :
SunOS 5.10 Version Generic_141445-09 32-bit"
...
Configuring devices.
Custom JumpStart
Reading ZFS config: done
Setting up Java. Please wait ...
NOTE: Not enough memory for graphical installation. Graphical... (4 Replies)
Discussion started by: TomSu
4 Replies
8. Solaris
I have a jumpstart client that is not requesting the tftp boot file. The rarp function is working, hostname and ip are set ok, but it hangs after that.
tcpdump output:
jumpstart-server:/var/lib/tftpboot# tcpdump -i eth1
tcpdump: verbose output suppressed, use -v or -vv for full protocol... (6 Replies)
Discussion started by: skitch
6 Replies
9. Solaris
I am trying to install Solaris x86 using the Jumpstart server. I run the add_install_client command with appropriate options, and reboot my x86 Target box. The installation starts fine and unattended. After the installation completes and the target goes for a re-boot, it does not boot from the HDD... (9 Replies)
Discussion started by: hemalsid
9 Replies
10. Solaris
Installing Solaris x86 using jumpstart does not set the hostname for the target. Any idea where do we need to specify hostname to be set for jumpstart installation. (1 Reply)
Discussion started by: hemalsid
1 Replies
LEARN ABOUT V7
install-solaris
install-solaris(1M) install-solaris(1M)
NAME
install-solaris - install the Solaris operating system
SYNOPSIS
install-solaris
install-solaris invokes the Solaris Install program. Depending on graphical capability and available memory at the time of invocation,
install-solaris invokes either a text-based installer or a graphical installer.
The following minimum requirements for physical memory dictate which features are available during installation:
For SPARC machines:
128 MB
Minimum physical memory for all installation types
128 MB
Minimum physical memory required for windowing system
384 MB
Minimum physical memory required for graphical-based installation
For x86 machines:
256 MB
Minimum physical memory for all installation types
256 MB
Minimum physical memory required for windowing system
512 MB
Minimum physical memory required for graphical-based installation
In some cases, even if the minimum physical memory is present, available virtual memory after system startup can limit the number of fea-
tures available.
install-solaris exists only on the Solaris installation media (CD or DVD) and should be invoked only from there. Refer to the for more
details.
install-solaris allows installation of the operating system onto any standalone system. install-solaris loads the software available on the
installation media. Refer to the for disk space requirements.
Refer to the for more information on the various menus and selections.
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcdrom (Solaris instal- |
| |lation media) |
+-----------------------------+-----------------------------+
|Interface Stability |Evolving |
+-----------------------------+-----------------------------+
pkginfo(1), install(1M), pkgadd(1M), attributes(5)
It is advisable to exit install-solaris by means of the exit options in the install-solaris menus.
23 Sep 2005 install-solaris(1M)