Sponsored Content
Full Discussion: Two NICs one IP address
Operating Systems Linux Two NICs one IP address Post 302244217 by wschmied on Tuesday 7th of October 2008 12:43:51 PM
Old 10-07-2008
Two NICs one IP address

I'm looking for a way in RHL 5.1 to use two NICs on one host with two physical IP addresses and map them under one virtual IP address, i.e. NIC 1 10.10.10.1 NIC2 10.10.10.2 VIP 192.168.10.1

Basically I want either one of the NICs to ARP for the VIP. No load balancing required just HA.
 

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Mac addresses of NICs (why are they the same)

I am training to be support on our solaris based network and was wondering why solaris seems to assign the same mac address to all NICs placed in the machine regardless of how many NICs are in there, when i do a ifconfig -a all nics have same MAC. Presumably this is a feature and there is... (1 Reply)
Discussion started by: hcclnoodles
1 Replies

2. IP Networking

HELP!! NICs went offline suddenly

I have a new server... We were doing some testing on it over the local ethernet. All was well in the night when we turned off the machine. In the morning we were unable to get the server online. Have changed cables, NICs, looked over network settings... all to no avail. I am running Redhat... (4 Replies)
Discussion started by: skotapal
4 Replies

3. IP Networking

3 nics, 2 with same network/mask

I run openbsd with 3 NICs, ep1 is dhcp, interface with internet ip addy dc0 is 192.168.0.254/24 sis0 is 192.168.0.253/24 My system somehow lags, and some services do not work properly, i want to run a lot of local network services like samba, named, ftp, http, dhcpd, radiusd. output of... (1 Reply)
Discussion started by: hachik
1 Replies

4. AIX

Merge NICs

Hi friends, I installed oracle 10g (10.2.0.2) RAC on 2 IBM p5 570 servers running AIX 5.3ML04 and HACMP5.2 (used Raw devices, not used GPFS). Each server has 4 x 1Gbps ethernet cards (NICs), en0 and en1 for boot address, en2 and en3 for oracle interconnect. Now i want to merge 2 NICs (en2 and... (1 Reply)
Discussion started by: bong02
1 Replies

5. IP Networking

FreeBSD and two NICs

FreeBSD 4.8, Apache 1.3.27 - two NICs, one with a real-world IP plugged into a switch outside the PIX firewall, the other with a private IP plugged into a switch inside the PIX firewall. Apache listens on both IPs. my domain is mydomain.org. so in /etc/rc.conf i have something like this (these... (10 Replies)
Discussion started by: ednix
10 Replies

6. Solaris

How many NICS do I have?

Hi, is there a way in Solaris 8 to determine how many total NIC's say a Sun Sparc box has installed - plumbed or unplumbed - and find out its capable network speeds and MAC address? I know ifconfig -a but that only shows the plumbed and used interfaces. thx cc (2 Replies)
Discussion started by: bigapple100
2 Replies

7. UNIX for Dummies Questions & Answers

multiple NICS in one box

Help, I have a Ubuntu headless server that has 5 NICs in it. The eth0-4 interfaces keep moving from NIC to NIC on boot up. I am told that there is a file that I can edit that will allow me to stabilize this but I need some help in determining the exact file and format for that file. All help will... (0 Replies)
Discussion started by: poundjd
0 Replies

8. Red Hat

how to combine nics for DM Multipath

I don't undestand how to combine 4 nics in order to use DM Multipath. Do I have to install each nic with its IP address? If yes, do I need a group IP address? This concept is not clear for me. The connection beetwen the server (DELL Poweredge T710) and the SAN through iscsi works well, I used... (1 Reply)
Discussion started by: gnupinux
1 Replies

9. IP Networking

Networking 2 NICs

Hi all, Host - Ubuntu 12.04 desktop 64bit Virtualizer - Oracle VirtualBox 2 NICs Where can I find relevant document to set up 2 NICs, one for inward bound and another for outward bound, separate channel, both connected to the same router Would following document be appropriate for my... (1 Reply)
Discussion started by: satimis
1 Replies

10. UNIX for Dummies Questions & Answers

Linux with two NICs

Hello All, I have Linux box with two interface cards. Every card has it's own IP Address and Gateway, IP addresses are from different subnets. eth0 192.168.1.10/24 GW 192.168.1.1 eth1 192.168.2.10/24 GW 192.168.2.1 Third PC is located in 192.168.13.0/24 network and is trying to access... (2 Replies)
Discussion started by: AndreiM
2 Replies
svatophys(9r)															     svatophys(9r)

NAME
svatophys - General: Converts a system virtual address to a physical address SYNOPSIS
kern_return_t svatophys( vm_offset_t kern_addr, vm_offset_t *phys_addr ); ARGUMENTS
Specifies the kernel virtual address. Specifies a pointer to the physical address to be filled in. DESCRIPTION
The svatophys routine converts a system virtual address to the corresponding physical address. All address and data structure manipulation done within the kernel is performed using system virtual addresses. Typically, system virtual addresses are a means of mapping physical memory and I/O space, which often consists of device registers and DMA buffers. In contrast to this, devices are usually unaware of any virtual addressing and for this reason use physical addresses. You use the svatophys routine to perform this address translation. As an example of where you can use this address translation, a disk device driver can use DMA buffers to transfer blocks of data to the disk (for the case of a write operation). The data to be written to disk is present in system memory at a system virtual address known to the driver. To initiate the DMA operation, the disk driver can set up a command packet to specify a write operation to the underlying disk controller hardware. This write command packet contains (among other things) the location of the DMA buffer as a physical address and the length of the buffer. Here, the driver calls the svatophys routine to translate the system virtual address of the DMA buffer to a physical address in the command packet issued to the disk driver. RETURN VALUES
The svatophys routine returns the following: The address translation has been completed successfully. Unable to perform address transla- tion. This value indicates that the address specified by the kern_addr argument is not a valid kernel or system virtual address. svatophys(9r)
All times are GMT -4. The time now is 06:09 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy