Sponsored Content
Operating Systems Solaris Connect Solaris 10 to NetApp filer using Emulex single port HBAs. Post 302244171 by pupp on Tuesday 7th of October 2008 10:55:20 AM
Old 10-07-2008
does your system see the devices? did you install and boot -r ?

next you'll need the emulex drivers. if you bought it outta the box, grab the software. otherwise go to emulex site. you should install those packages. lputil, emlxinfo, emulexadm and so on. check out Sun StorageTek Enterprise PCI-X 4 Gb FC Single and Dual Port Emulex Host Bus Adapters Insallation and Basic Interoperability Guide

as for mpxio... check out C H A P T E R 3 - Administering Multipathing Devices Through mpathadm Commands

that should get you going.

Last edited by pupp; 10-07-2008 at 12:03 PM.. Reason: link kind of was screwed up :D
 

9 More Discussions You Might Find Interesting

1. Solaris

Use DFM Netapp 3.01 R1 on Solaris 8

I have this problem when i integrate a new san switch in DFM 3.01 R1 : dfm fcswitch add switchname1 Error: Host switchname2 (11197) already exists. switchname2 is a similar san switch but in another fabric, switchname2 is already integrated in DFM database. Bests Regards Olivier (2 Replies)
Discussion started by: omainfroy
2 Replies

2. Solaris

emulex card on solaris 9

Hello, I am new on solaris. We will connect our sun solaris system to the SAN and add 2 Emulex card on the system (solaris 9). Who have already done this and can give me the procedure to follow ? driver to install multipath etc... Thanks in advance Emmanuel (1 Reply)
Discussion started by: emma32
1 Replies

3. UNIX for Advanced & Expert Users

Solaris 10 x86_64 - Emulex Fibrechannel drivers

Hello! I'm having problems to install Emulex fibrechannel card drivers to a HP DL580 G5 running Solaris 10 x86_64. Any of you guys had this problem or knows the answer? =) cfgadm gives me the following info, which seems to say that it is ok? But the card has'nt logged into the switch... (0 Replies)
Discussion started by: Esaia
0 Replies

4. Solaris

Netapp filer LUN Resize. Commands to run on Solaris afterwards.

Hi, I need to increase a veritas filesystem I have currently mounted on a Solaris 10 server. We can resize the LUN on the NetApp filer no problem. What I need to know is what do I do next on the Solaris 10 server I have so that it will see the increase in size. Do I run 'devfsadm' to... (3 Replies)
Discussion started by: gwhelan
3 Replies

5. Solaris

Can't see Netapp LUN on Solaris using LPFC after reboot.

Hi, I've just edited this post. I found the solution for this. Thanks. (0 Replies)
Discussion started by: gwhelan
0 Replies

6. Solaris

Solaris 10 / NetApp volumes - Forbidden: You don't have permission to access...

Hi all We have a couple of solaris zones running a jboss app in a cluster. Each zone has a shared netapp volume mounted to /app/xxx with everything under that subdir apart from jboss which is local to each zone in /app/jboss-3.2.5 There is a symlink in /app/xxx/jboss-3.2.5 which points to... (0 Replies)
Discussion started by: skewbie
0 Replies

7. Solaris

Netapp filer details - command?

What command can I use to find out details about a netapp filer. I have a directory that is a filer i would like to know details about the source host/folder that it points to. Thanks. (2 Replies)
Discussion started by: jjohnson
2 Replies

8. Solaris

How to mount a NetApp snapshoot to a Solaris server?

Hi I have NetApp lun, that was mounted on server as a file system that failed, and that server is no longer in use, but I would like to use that file system on another server. The NetApp Admin, told me he can present that lun to my other system, but my problem is how to mount it? Because that... (8 Replies)
Discussion started by: fretagi
8 Replies

9. Solaris

Solaris 10 installing on Cisco UCS doesn't see HBAs

The chassis config is right... this blade can boot to VMware ESXi and see HBAs and LUNs. Solaris isn't seeing the HBAs at all... luxadm probe returns ERROR: No Fibre Channel Adapters found. fcinfo hba-port -l returns No Adapters Found. prtdiag -v gets me: ==== Upgradeable Slots... (3 Replies)
Discussion started by: jnojr
3 Replies
purple-url-handler(1)						   User Commands					     purple-url-handler(1)

NAME
purple-url-handler - Python script to handle URL with purple SYNOPSIS
purple-url-handler [-URL] DESCRIPTION
Python script to handle URL with purple. OPTIONS
Usage: purple-url-handler URL Example: purple-url-handler "xmpp:romeo@montague.net?message" ATTRIBUTES
See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Availability |SUNWgnome-im-client | +-----------------------------+-----------------------------+ |Interface stability |Volatile | +-----------------------------+-----------------------------+ SEE ALSO
purple-remote(1), purple-send(1), purple-send-async(1), attributes(5) purple-url-handler Manual, http://pidgin.im/ NOTES
Updated by Lei Ju, Sun Microsystems Inc., 2006, 2007. SunOS 5.11 02 Apr 2008 purple-url-handler(1)
All times are GMT -4. The time now is 12:41 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy