10-02-2008
hi,
i think netstat -an would be a nice and simple method to see whether the server has reach its maximum port caused by application forking.
and for the serious part - a NIDS or NIPS should be placed in front of all servers network.
HTH.
9 More Discussions You Might Find Interesting
1. SCO
Hi,
Wonder is someone can help.
I've got a server SCO_SV 3.2v5.0.7 PentIII that is located at a different site and is running slow and has been for a week. I've been speaking to a third party who say nothing is wrong with it but its still running slow.
The 3rd party advise it could be a... (2 Replies)
Discussion started by: tez
2 Replies
2. Post Here to Contact Site Administrators and Moderators
Hi Guys,
Since last 20-30 min Server was Too slow ..even few of times i got Database connection error.
Thanks
Sanjay Tripathi (0 Replies)
Discussion started by: SanjayLinux
0 Replies
3. HP-UX
Hi,
Since last week our server become too slow when we try to run application on it. When we run top command, it show as below:
So it's nothing to do with heavy utilization, right? Can you give some opinion on what actually had happended?
Thank you very much... :b: (4 Replies)
Discussion started by: yeazas
4 Replies
4. UNIX for Dummies Questions & Answers
Hi,
Following my last post I've mounted the remote server on my local server. However copying files from this mounted server is increadbily slow. If I copy files using rcp it's very fast so I assume there must be a setting somewhere?
Any help appreicated.
Thanks (2 Replies)
Discussion started by: AngryBunny
2 Replies
5. UNIX for Dummies Questions & Answers
Hi guyes our linux server is very slow today and load average is more than 16 .I m new in linux request you to kindly help resolving the issue.
Where can i find the log for the cause.
# lsb_release -a
LSB Version: ... (2 Replies)
Discussion started by: pinga123
2 Replies
6. Solaris
I recently configured a WANBoot server on a Ldom 2.0 running Solaris10u9 with ZFS root. When i start the installation form the client with
Ok Boot net - install ,
it takes at least 20-25 minutes just to download the miniroot on the client .. i read there was a bug on T servers firmware... (2 Replies)
Discussion started by: fugitive
2 Replies
7. Infrastructure Monitoring
There is a big problem with the server (VPS based on OpenVZ, CentOS 5, 3GB RAM). The problem is the following. The first 15-20 minutes after starting the server is operating normally, the load average is less than or about 1.0, but then begins to increase sharply% wa, then hovers around 95-99%.... (2 Replies)
Discussion started by: draiphod
2 Replies
8. Linux
Hello everyone,
I've installed squid proxy server in Linux centos machine for users.actually problem is when users browse some websites eg : WordPress.org, gravatar.com it loads very slow compare to others sites .my line is 4mbps and only 6 users for it.I've bypassed squid for myself via... (3 Replies)
Discussion started by: afybiz
3 Replies
9. AIX
Hello,
All the commands on AIX are running very slow.
Below is few stats but I didn't find any issue in cpu or memory reosurces
vmstat
System configuration: lcpu=4 mem=6144MB ent=1.00
kthr memory page faults cpu
----- -----------... (2 Replies)
Discussion started by: Vishal_dba
2 Replies
LEARN ABOUT DEBIAN
sys::statistics::linux::cpustats
Sys::Statistics::Linux::CpuStats(3pm) User Contributed Perl Documentation Sys::Statistics::Linux::CpuStats(3pm)
NAME
Sys::Statistics::Linux::CpuStats - Collect linux cpu statistics.
SYNOPSIS
use Sys::Statistics::Linux::CpuStats;
my $lxs = Sys::Statistics::Linux::CpuStats->new;
$lxs->init;
sleep 1;
my $stats = $lxs->get;
Or
my $lxs = Sys::Statistics::Linux::CpuStats->new(initfile => $file);
$lxs->init;
my $stats = $lxs->get;
DESCRIPTION
Sys::Statistics::Linux::CpuStats gathers cpu statistics from the virtual /proc filesystem (procfs).
For more information read the documentation of the front-end module Sys::Statistics::Linux.
CPU STATISTICS
Generated by /proc/stat for each cpu (cpu0, cpu1 ...). cpu without a number is the summary.
user - Percentage of CPU utilization at the user level.
nice - Percentage of CPU utilization at the user level with nice priority.
system - Percentage of CPU utilization at the system level.
idle - Percentage of time the CPU is in idle state.
total - Total percentage of CPU utilization.
Statistics with kernels >= 2.6.
iowait - Percentage of time the CPU is in idle state because an I/O operation
is waiting to complete.
irq - Percentage of time the CPU is servicing interrupts.
softirq - Percentage of time the CPU is servicing softirqs.
steal - Percentage of stolen CPU time, which is the time spent in other
operating systems when running in a virtualized environment (>=2.6.11).
METHODS
new()
Call "new()" to create a new object.
my $lxs = Sys::Statistics::Linux::CpuStats->new;
Maybe you want to store/load the initial statistics to/from a file:
my $lxs = Sys::Statistics::Linux::CpuStats->new(initfile => '/tmp/cpustats.yml');
If you set "initfile" it's not necessary to call sleep before "get()".
It's also possible to set the path to the proc filesystem.
Sys::Statistics::Linux::CpuStats->new(
files => {
# This is the default
path => '/proc'
stat => 'stat',
}
);
init()
Call "init()" to initialize the statistics.
$lxs->init;
get()
Call "get()" to get the statistics. "get()" returns the statistics as a hash reference.
my $stats = $lxs->get;
raw()
Get raw values.
EXPORTS
No exports.
SEE ALSO
proc(5)
REPORTING BUGS
Please report all bugs to <jschulz.cpan(at)bloonix.de>.
AUTHOR
Jonny Schulz <jschulz.cpan(at)bloonix.de>.
COPYRIGHT
Copyright (c) 2006, 2007 by Jonny Schulz. All rights reserved.
This program is free software; you can redistribute it and/or modify it under the same terms as Perl itself.
perl v5.14.2 2012-03-09 Sys::Statistics::Linux::CpuStats(3pm)