I installed a FC array for the first time and everything looks OK
in mpathadm, cfgadm, but I don't know what to do next.
Code:
# stmsboot -L
non-STMS device name STMS device name
------------------------------------------------------------------
/dev/rdsk/c2t1d0 /dev/rdsk/c4t600A0B80004876380000035348E0A274d0
/dev/rdsk/c3t5d0 /dev/rdsk/c4t600A0B80004876380000035348E0A274d0
Code:
# format
Searching for disks...done
c2t1d31: configured with capacity of 16.00MB
c3t5d31: configured with capacity of 16.00MB
c4t600A0B80004876380000035348E0A274d0: configured with capacity of 272.44GB
AVAILABLE DISK SELECTIONS:
0. c1t0d0 <LSILOGIC-LogicalVolume-3000 cyl 65533 alt 2 hd 16 sec 273>
/pci@400/pci@0/pci@8/scsi@0/sd@0,0
1. c2t1d31 <SUN-UniversalXport-0660 cyl 8 alt 2 hd 64 sec 64>
/pci@500/pci@0/pci@c/SUNW,qlc@0/fp@0,0/ssd@w200400a0b8487639,1f
2. c3t5d31 <SUN-UniversalXport-0660 cyl 8 alt 2 hd 64 sec 64>
/pci@500/pci@0/pci@d/SUNW,qlc@0/fp@0,0/ssd@w200500a0b8487639,1f
3. c4t600A0B80004876380000035348E0A274d0 <SUN-CSM200_R-0660 cyl 34872 alt 2 hd 256 sec 64>
/scsi_vhci/ssd@g600a0b80004876380000035348e0a274
Specify disk (enter its number):
If I select 3 it says
[disk formated]
Disk no labeled. Label it now?
I used the Common Array Manager (CAM) to set this up with a pool,
virtual disks, and hosts, but should I format the disk?
What is the next procedure here to view the 272 GB?
This is correct behavior. This disk does not currently have a label which is recognised by Solaris.
What you need to do is to choose disk 3 and tell it to label the device. If it prompts you with a menu, you choose "Auto" and write this label to the disk. Once Solaris has labelled this disk, you shouldn't have to do it again.
I need information what maximum error level on FC card need clasification of critical level (SAN mass storidge)
Please write screenshot from utility fcutil whith test option.
Pawel (0 Replies)
Hi,
We have 12x1TB SATA disks in our array and I need to create 10TB volume. I defined new storage profile on array and when I tried to add volume, I faced with ~2TB limit for new volumes. I didn't find how to set another limit on my storage profile. Is there is a way to configure one large... (3 Replies)
Hello,
Wondering if anyone can help me with mounting a file share from my Sun T2000 server running Solaris 10 to my connected 2530 disk array?
I believe I've connected the disk array correctly and I have created a volume on the array using the filesystem (Sun_SAM-FS, RAID-5).
The T2000... (15 Replies)
Hi!
I have Sun StorageTek 2540 FC array and CAM works very slowly - I can wait for software response even more than 2 minutes... I run this software on Windows machine with Firefox Web Browser but speed is terrible... How can I make it works at least a little bit faster?.. (2 Replies)
In Sun manuals, I didn't find how to backup Sun StorageTek Common Array Manager's configuration. Is there a way to do it like backing up Brocade switch configuration? CAM is under Solaris 10.
Thank you in advance! (0 Replies)
Hi,
I have a question about Sun StorageTek Common Array Manager (CAM): What is the concept of 'host'? Is it the hostname of the server that has access to the managed array? If so, can I use its IP instead of its hostname?
I've found a 'host' under CAM called XYZ (See below). In our... (7 Replies)
Bought a Sun StorageTek 2540 SAN array a few years ago from a company that was going out of business. When we first set it up, we were able to get all the software (Common Array Manager) and firmware directly from Sun.
We just upgraded the drives, but the array is too large for the firmware. Now... (6 Replies)
hi everone
i am experiencing disconnectivity from storage to My database machines. i have doubt on my FC cards in my sparc T4-2 machines. i want to know how should i check from my solaris that whether the cards are ok or not because once the disks get disconnect from SAN so it come back again but... (5 Replies)
Discussion started by: janakors
5 Replies
LEARN ABOUT OPENSOLARIS
mlib_signalsplit_s16_s16s
mlib_SignalSplit_S16_S16S(3MLIB) mediaLib Library Functions mlib_SignalSplit_S16_S16S(3MLIB)NAME
mlib_SignalSplit_S16_S16S - split
SYNOPSIS
cc [ flag... ] file... -lmlib [ library... ]
#include <mlib.h>
mlib_status mlib_SignalSplit_S16_S16S(mlib_s16 *ch0,
mlib_s16 *ch1, const mlib_s16 *src, mlib_s32 n);
DESCRIPTION
The following function splits a stereo signal array into two signal arrays.
PARAMETERS
The function takes the following arguments:
ch0 Destination signal array of Channel 0.
ch1 Destination signal array of Channel 1.
src Source stereo signal array. src[2*i] contains Channel 0, and src[2*i+1] contains Channel 1.
n Number of samples in the source signal array.
RETURN VALUES
The function returns MLIB_SUCCESS if successful. Otherwise it returns MLIB_FAILURE.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Interface Stability |Committed |
+-----------------------------+-----------------------------+
|MT-Level |MT-Safe |
+-----------------------------+-----------------------------+
SEE ALSO mlib_SignalMerge_S16S_S16(3MLIB), attributes(5)SunOS 5.11 2 Mar 2007 mlib_SignalSplit_S16_S16S(3MLIB)
10-01-2008
