I installed a FC array for the first time and everything looks OK
in mpathadm, cfgadm, but I don't know what to do next.
Code:
# stmsboot -L
non-STMS device name STMS device name
------------------------------------------------------------------
/dev/rdsk/c2t1d0 /dev/rdsk/c4t600A0B80004876380000035348E0A274d0
/dev/rdsk/c3t5d0 /dev/rdsk/c4t600A0B80004876380000035348E0A274d0
Code:
# format
Searching for disks...done
c2t1d31: configured with capacity of 16.00MB
c3t5d31: configured with capacity of 16.00MB
c4t600A0B80004876380000035348E0A274d0: configured with capacity of 272.44GB
AVAILABLE DISK SELECTIONS:
0. c1t0d0 <LSILOGIC-LogicalVolume-3000 cyl 65533 alt 2 hd 16 sec 273>
/pci@400/pci@0/pci@8/scsi@0/sd@0,0
1. c2t1d31 <SUN-UniversalXport-0660 cyl 8 alt 2 hd 64 sec 64>
/pci@500/pci@0/pci@c/SUNW,qlc@0/fp@0,0/ssd@w200400a0b8487639,1f
2. c3t5d31 <SUN-UniversalXport-0660 cyl 8 alt 2 hd 64 sec 64>
/pci@500/pci@0/pci@d/SUNW,qlc@0/fp@0,0/ssd@w200500a0b8487639,1f
3. c4t600A0B80004876380000035348E0A274d0 <SUN-CSM200_R-0660 cyl 34872 alt 2 hd 256 sec 64>
/scsi_vhci/ssd@g600a0b80004876380000035348e0a274
Specify disk (enter its number):
If I select 3 it says
[disk formated]
Disk no labeled. Label it now?
I used the Common Array Manager (CAM) to set this up with a pool,
virtual disks, and hosts, but should I format the disk?
What is the next procedure here to view the 272 GB?
This is correct behavior. This disk does not currently have a label which is recognised by Solaris.
What you need to do is to choose disk 3 and tell it to label the device. If it prompts you with a menu, you choose "Auto" and write this label to the disk. Once Solaris has labelled this disk, you shouldn't have to do it again.
I need information what maximum error level on FC card need clasification of critical level (SAN mass storidge)
Please write screenshot from utility fcutil whith test option.
Pawel (0 Replies)
Hi,
We have 12x1TB SATA disks in our array and I need to create 10TB volume. I defined new storage profile on array and when I tried to add volume, I faced with ~2TB limit for new volumes. I didn't find how to set another limit on my storage profile. Is there is a way to configure one large... (3 Replies)
Hello,
Wondering if anyone can help me with mounting a file share from my Sun T2000 server running Solaris 10 to my connected 2530 disk array?
I believe I've connected the disk array correctly and I have created a volume on the array using the filesystem (Sun_SAM-FS, RAID-5).
The T2000... (15 Replies)
Hi!
I have Sun StorageTek 2540 FC array and CAM works very slowly - I can wait for software response even more than 2 minutes... I run this software on Windows machine with Firefox Web Browser but speed is terrible... How can I make it works at least a little bit faster?.. (2 Replies)
In Sun manuals, I didn't find how to backup Sun StorageTek Common Array Manager's configuration. Is there a way to do it like backing up Brocade switch configuration? CAM is under Solaris 10.
Thank you in advance! (0 Replies)
Hi,
I have a question about Sun StorageTek Common Array Manager (CAM): What is the concept of 'host'? Is it the hostname of the server that has access to the managed array? If so, can I use its IP instead of its hostname?
I've found a 'host' under CAM called XYZ (See below). In our... (7 Replies)
Bought a Sun StorageTek 2540 SAN array a few years ago from a company that was going out of business. When we first set it up, we were able to get all the software (Common Array Manager) and firmware directly from Sun.
We just upgraded the drives, but the array is too large for the firmware. Now... (6 Replies)
hi everone
i am experiencing disconnectivity from storage to My database machines. i have doubt on my FC cards in my sparc T4-2 machines. i want to know how should i check from my solaris that whether the cards are ok or not because once the disks get disconnect from SAN so it come back again but... (5 Replies)
Discussion started by: janakors
5 Replies
LEARN ABOUT CENTOS
paps
PAPS(1) General Commands Manual PAPS(1)NAME
paps - UTF-8 to PostScript converter using Pango
SYNOPSIS
paps [options] files...
DESCRIPTION
paps reads a UTF-8 encoded file and generates a PostScript language rendering of the file. The rendering is done by creating outline curves
through the pango ft2 backend.
OPTIONS
These programs follow the usual GNU command line syntax, with long options starting with two dashes (`-'). A summary of options is
included below.
--landscape
Landscape output. Default is portrait.
--columns=cl
Number of columns output. Default is 1.
--font=desc
Set the font description. Default is Monospace 12.
--rtl Do rtl layout.
--paper ps
Choose paper size. Known paper sizes are legal, letter, a4. Default is A4.
--bottom-margin=bm
Set bottom margin in postscript points (1/72 inch). Default is 36.
--top-margin=tm
Set top margin. Default is 36.
--left-margin=lm
Set left margin. Default is 36.
--right-margin=rm
Set right margin. Default is 36.
--help Show summary of options.
--header
Draw page header for each page.
--markup
Interpret the text as pango markup.
--encoding=ENCODING
Assume the documentation encoding is ENCODING.
--lpi Set the lines per inch. This determines the line spacing.
--cpi Set the characters per inch. This is an alternative method of specifying the font size.
--stretch-chars
Indicates that characters should be stretched in the y-direction to fill up their vertical space. This is similar to the texttops
behaviour.
AUTHOR
paps was written by Dov Grobgeld <dov.grobgeld@gmail.com>.
This manual page was written by Lior Kaplan <kaplan@debian.org>, for the Debian project (but may be used by others).
April 17, 2006 PAPS(1)
10-01-2008
