Sponsored Content
Full Discussion: Network interface issue
Operating Systems Solaris Network interface issue Post 302241534 by kumarmani on Monday 29th of September 2008 02:54:55 PM
Old 09-29-2008
Network interface issue

Hi All,

I want to configure network into my system.

i tried following in to configure the interface

to find the name of interface

#prtdiag |grep net

i got following

0 PCI-1 33 1 network-SUNW, hme

then i tried following

#prtconf -v |grep net

network, instance #0

not sure is above is what i tried plumbing the interface with following

#ifconfig hme plumb

i got error as

ifconfig: plumb:hme: no such interface

then i tried

#ifconfig hme

and got following

ifconfig: status:SIOCGLIFFLAGS: hme: no such interface


please suggest as what could be the reason for same
:
 

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Network Interface

Hi ! Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !! Thx in adivance ! Witt (4 Replies)
Discussion started by: witt
4 Replies

2. Solaris

Network Interface Issue

Hi all, Here im facing problem with NIC Interface with my X86 Version of Solaris Express, even after loading module for that Interface. So please check this below mentioned log for your use and get back to me ASAP. - - - -- --... (0 Replies)
Discussion started by: baraghun
0 Replies

3. Solaris

configure zones to have different network interface and network

i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ? Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies

4. Solaris

Network interface not recoginized

Hello, I have Windows and Solaris 10 installed on HP Pavalion. Both of the operating system are installed on separate drives. Network card is recognized on Windows but Solaris doesn't seem to recognize it for some reason. So far I have tried sys-unconfig but it didn't really help. Please... (3 Replies)
Discussion started by: saudsos
3 Replies

5. UNIX and Linux Applications

Access to network interface (Mac-network)

Hi, I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan. For that I must access to network interface to develope my personal stack based on standard 802.15.4. Can you help me? I need an explanation for that. (0 Replies)
Discussion started by: berny88
0 Replies

6. IP Networking

Network interface-

Hello, Please what's the difference between: AND Thank you so much (3 Replies)
Discussion started by: chercheur857
3 Replies

7. IP Networking

network interface -

Hello, Please, how can i create a network interface with a routable IP address on linux (ubuntu) ? AND How can i desactivate an interface? Thank you so much for help. (1 Reply)
Discussion started by: chercheur857
1 Replies

8. Red Hat

Redhat disabling network interface - IRQ issue

Hi. I'm having problems on multiple Red Hat VM's (on esxi) whereby the network interface IRQ is disabled by the OS. This is the error from dmesg: command: Write(10): 2a 00 03 42 3f e0 00 00 08 00 mptscsih: ioc0: task abort: SUCCESS (sc=ffff81018b45c680) irq 67: nobody cared (try... (0 Replies)
Discussion started by: badoshi
0 Replies

9. Solaris

No network cable But Network interface is UP and Running

I've one Netra 240 After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces. I tried to restart and plumb/unplumb with no luck. ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies

10. UNIX for Dummies Questions & Answers

Adding a network interface to a bonded interface

I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
HME(4)							   BSD Kernel Interfaces Manual 						    HME(4)

NAME
hme -- Sun Microelectronics STP2002-STQ Ethernet interfaces device driver SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file: device miibus device hme Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5): if_hme_load="YES" DESCRIPTION
The hme driver supports Sun Microelectronics STP2002-STQ ``Happy Meal Ethernet'' Fast Ethernet interfaces. All controllers supported by the hme driver have TCP checksum offload capability for both receive and transmit, support for the reception and transmission of extended frames for vlan(4) and a 128-bit multicast hash filter. HARDWARE
The hme driver supports the on-board Ethernet interfaces of many Sun UltraSPARC workstation and server models. Cards supported by the hme driver include: o Sun PCI SunSwift Adapter (``SUNW,hme'') o Sun SBus SunSwift Adapter (``hme'' and ``SUNW,hme'') o Sun PCI Sun100BaseT Adapter 2.0 (``SUNW,hme'') o Sun SBus Sun100BaseT 2.0 (``SUNW,hme'') o Sun PCI Quad FastEthernet Controller (``SUNW,qfe'') o Sun SBus Quad FastEthernet Controller (``SUNW,qfe'') NOTES
On sparc64 the hme driver respects the local-mac-address? system configuration variable which can be set in the Open Firmware boot monitor using the setenv command or by eeprom(8). If set to ``false'' (the default), the hme driver will use the system's default MAC address for all of its devices. If set to ``true'', the unique MAC address of each interface is used if present rather than the system's default MAC address. Supported interfaces having their own MAC address include on-board versions on boards equipped with more than one Ethernet interface and all add-on cards except the single-port SBus versions. SEE ALSO
altq(4), intro(4), miibus(4), netintro(4), vlan(4), eeprom(8), ifconfig(8) Sun Microelectronics, STP2002QFP Fast Ethernet, Parallel Port, SCSI (FEPS) User's Guide, April 1996, http://mediacast.sun.com/users/Barton808/media/STP2002QFP-FEPs_UG.pdf. HISTORY
The hme driver first appeared in NetBSD 1.5. The first FreeBSD version to include it was FreeBSD 5.0. AUTHORS
The hme driver was written by Paul Kranenburg <pk@NetBSD.org>. BSD
June 14, 2009 BSD
All times are GMT -4. The time now is 04:26 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy