09-18-2008
raw device in Linux
Hello group,
Is it possible to use partition on a disk as a raw device? I have a LUN on a SAN which I would like to partition and use those partitions as raw device.
If it is feasable, how do I bind them to a device?
For example, say sdd has 3 partitions on it, sdd1, sdd2 and sdd3. Can I bind them in the following manner:
raw /dev/raw/raw1 /dev/sdd1
raw /dev/raw/raw2 /dev/sdd2
raw /dev/raw/raw3 /dev/sdd3
Thanks in advance,
Bernard
9 More Discussions You Might Find Interesting
1. AIX
Hy
I have several logical volumes that are turned into raw devices used by Informix DB. I would like to add some more.
In /dev directory i see logical volumes as block files: lv_name1, lv_name2 ...
and
i see raw devices defined as character files:
rlv_name1, rlv_name2 ...
As i see,... (5 Replies)
Discussion started by: veccinho
5 Replies
2. Solaris
Hi All ,
I would like to know the procedure for increasing shared volume space in sun cluster .
Currently the configuration is like these .
Main stripe
oradb1/d91 2 1 /dev/did/rdsk/d35s0 1 /dev/did/rdsk/d36s0 =Total 49 Gb
oradb1/d94 -p oradb1/d91 -o 88080480 -b 14680064 ==Total 7 GB... (4 Replies)
Discussion started by: sahil_shine
4 Replies
3. AIX
Please consider this a question about basics&best practices. On AIX 5.3 system, three raw physical volumes are defined from storage. While doing a read with command dd from the raw device, the speed rate is 250Mb/s.
Then, it gets complex when I define these three pv's to an lv of type raw. Doing... (4 Replies)
Discussion started by: royalliege
4 Replies
4. Solaris
Hi,
I am using Sun Solaris 10 (Sparc 64 bit),
I have a meta device /dev/dsk/emcpower26a mounting on /u01. I want to make this metadeice as raw device.
Need solaris command to remove file system and make it as raw device ?.
Is there any solaris command to check raw devices ?.
Thanks (1 Reply)
Discussion started by: zeeshan047
1 Replies
5. Solaris
Hi,
I need to create 4 zones.
I have an array with a RAID5 volume. I have exported 4 LUNS from the array. Now my host see the 4 LUNS as raw devices.
I am partitioning each LUN using format then mounting each slice on the global zone. Then I am using each slice as a file system for my non... (3 Replies)
Discussion started by: general_lee
3 Replies
6. Red Hat
Hi All,
Hope someone can help me with this.
I have noticed that on some of the servers i am currently administering there is a difference in the setup of some of the LVM disks.
Some of the disks have been created by SN disk allocated, disk partitioned using type 8e over the entire disk,... (2 Replies)
Discussion started by: Tommyk
2 Replies
7. Solaris
Hi,
I'm trying to find out how to see used space on RAW device.
I tried with prtvtoc -f RAWdevice but for 3 different device I'm getting the same FREE_SIZE which look a bit impossible.
root@zg8cscfb1> prtvtoc -f /dev/md/redodg/rdsk/d300
FREE_START=0 FREE_SIZE=20352 FREE_COUNT=1 FREE_PART=... (2 Replies)
Discussion started by: MarioT
2 Replies
8. UNIX for Dummies Questions & Answers
HI,
I want to start Oracle on UNIX machine, now the , it is failing to startup because it cannot identify a raw device. Actually machine was rebooted and now we need to mount the devices, but i just want to know the command/way to mount or rather start/init a raw device. Please let me know. (2 Replies)
Discussion started by: Onkar Banerjee
2 Replies
9. Red Hat
Hi,
How to find the raw device/multipath details of the LUN used by the diskgroups of the database.
file system type -- ASM
Oracle -- 11.2.0.3.0
OS -- Linux
This is RAC database.
Regards,
Maddy (2 Replies)
Discussion started by: Maddy123
2 Replies
PARTX(8) System Administration PARTX(8)
NAME
partx - tell the Linux kernel about the presence and numbering of on-disk partitions
SYNOPSIS
partx [-a|-d|-s] [-t TYPE] [-n M:N] [-] disk
partx [-a|-d|-s] [-t TYPE] partition [disk]
DESCRIPTION
Given a device or disk-image, partx tries to parse the partition table and list its contents. It optionally adds or removes partitions.
The disk argument is optional when a partition argument is provided. To force scanning a partition as if it were a whole disk (for example
to list nested subpartitions), use the argument "-". For example:
partx --show - /dev/sda3
This will see sda3 as a whole-disk rather than a partition.
This is not an fdisk program -- adding and removing partitions does not change the disk, it just tells the kernel about the presence and
numbering of on-disk partitions.
OPTIONS
-a, --add
Add the specified partitions, or read the disk and add all partitions.
-b, --bytes
Print the SIZE column in bytes rather than in human-readable format.
-d, --delete
Delete the specified partitions or all partitions.
-g, --noheadings
Do not print a header line.
-l, --list
List the partitions. Note that all numbers are in 512-byte sectors. This output format is DEPRECATED in favour of --show. Don't
use it in newly written scripts.
-o, --output list
Define the output columns to use for --show and --raw output. If no output arrangement is specified, then a default set is used.
Use --help to get list of all supported columns.
-r, --raw
Use the raw output format.
-s, --show
List the partitions. All numbers (except SIZE) are in 512-byte sectors. The output columns can be rearranged with the --output
option.
-t, --type type
Specify the partition table type -- aix, bsd, dos, gpt, mac, minix, sgi, solaris_x86, sun, ultrix or unixware.
-n, --nr M:N
Specify the range of partitions. For backward compatibility also the format <M-N> is supported. The range may contain negative
numbers, for example "--nr :-1" means the last partition, and "--nr -2:-1" means the last two partitions. Supported range specifi-
cations are:
<M> Specifies just one partition (e.g. --nr 3).
<M:> Specifies lower limit only (e.g. --nr 2:).
<:N> Specifies upper limit only (e.g. --nr :4).
<M:N> or <M-N> Specifies lower and upper limits (e.g. --nr 2:4).
EXAMPLES
partx --show /dev/sdb3
partx --show --nr 3 /dev/sdb
partx --show /dev/sdb3 /dev/sdb
All three commands list partition 3 of /dev/sdb.
partx --show - /dev/sdb3
Lists all subpartitions on /dev/sdb3 (the device is used as whole-disk).
partx -o START -g --nr 3 /dev/sdb
Prints the start sector of partition 5 on /dev/sda without header.
partx -o SECTORS,SIZE /dev/sda5 /dev/sda
Lists the length in sectors and human-readable size of partition 5 on /dev/sda.
partx --add --nr 3:5 /dev/sdd
Adds all available partitions from 3 to 5 (inclusive) on /dev/sdd.
partx -d --nr :-1 /dev/sdd
Removes the last partition on /dev/sdd.
SEE ALSO
addpart(8), delpart(8), fdisk(8), parted(8), partprobe(8)
AUTHORS
Davidlohr Bueso <dave@gnu.org>
Karel Zak <kzak@redhat.com>
The original version was written by Andries E. Brouwer <aeb@cwi.nl>.
AVAILABILITY
The partx command is part of the util-linux package and is available from ftp://ftp.kernel.org/pub/linux/utils/util-linux/.
util-linux February 2011 PARTX(8)