GROWFS(8)						    BSD System Manager's Manual 						 GROWFS(8)

NAME

     growfs -- grow size of an existing ufs file system

SYNOPSIS

     growfs [-Ny] [-s size] special

DESCRIPTION

     The growfs utility extends the newfs(8) program.  Before starting growfs the disk must be labeled to a bigger size using bsdlabel(8).  If you
     wish to grow a file system beyond the boundary of the slice it resides in, you must re-size the slice using fdisk(8) before running growfs.
     If you are using volumes you must enlarge them by using vinum(8).	The growfs utility extends the size of the file system on the specified
     special file.  Currently growfs can only enlarge unmounted file systems.  Do not try enlarging a mounted file system, your system may panic
     and you will not be able to use the file system any longer.  Most of the newfs(8) options cannot be changed by growfs.  In fact, you can only
     increase the size of the file system.  Use tunefs(8) for other changes.

     The following options are available:

     -N      ``Test mode''.  Causes the new file system parameters to be printed out without actually enlarging the file system.

     -y      ``Expert mode''.  Usually growfs will ask you if you took a backup of your data before and will do some tests whether special is cur-
	     rently mounted or whether there are any active snapshots on the file system specified.  This will be suppressed.  So use this option
	     with great care!

     -s size
	     Determines the size of the file system after enlarging in sectors.  This value defaults to the size of the raw partition specified in
	     special (in other words, growfs will enlarge the file system to the size of the entire partition).

EXAMPLES

	   growfs -s 4194304 /dev/vinum/testvol

     will enlarge /dev/vinum/testvol up to 2GB if there is enough space in /dev/vinum/testvol.

SEE ALSO

     bsdlabel(8), dumpfs(8), fdisk(8), ffsinfo(8), fsck(8), newfs(8), tunefs(8), vinum(8)

HISTORY

     The growfs utility first appeared in FreeBSD 4.4.

AUTHORS

     Christoph Herrmann <chm@FreeBSD.org>
     Thomas-Henning von Kamptz <tomsoft@FreeBSD.org>
     The GROWFS team <growfs@Tomsoft.COM>

BUGS

     The growfs utility works starting with FreeBSD 3.x.  There may be cases on FreeBSD 3.x only, when growfs does not recognize properly whether
     or not the file system is mounted and exits with an error message.  Then please use growfs -y if you are sure that the file system is not
     mounted.  It is also recommended to always use fsck(8) after enlarging (just to be on the safe side).

     For enlarging beyond certain limits, it is essential to have some free blocks available in the first cylinder group.  If that space is not
     available in the first cylinder group, a critical data structure has to be relocated into one of the new available cylinder groups.  On
     FreeBSD 3.x this will cause problems with fsck(8) afterwards.  So fsck(8) needs to be patched if you want to use growfs for FreeBSD 3.x.
     This patch is already integrated in FreeBSD starting with FreeBSD 4.4.  To avoid an unexpected relocation of that structure it is possible to
     use ffsinfo -g 0 -l 4 on the first cylinder group to verify that nbfree in the CYLINDER SUMMARY (internal cs) of the CYLINDER GROUP cgr0 has
     enough blocks.  As a rule of thumb for default file system parameters one block is needed for every 2 GB of total file system size.

     Normally growfs writes this critical structure to disk and reads it again later for doing more updates.  This read operation will provide
     unexpected data when using -N.  Therefore, this part cannot really be simulated and will be skipped in test mode.

BSD
								 September 8, 2000							       BSD