09-17-2008
The problem may not be anything to do with configuration......
it maybe because you are using a straight cable and not a cross cable from your laptop
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Hi,
I have been facing a telnet problem with our SunOS 5.7 box. Initially we were facing porblems in login both from the console as well as through telnet. The machine was hard-booted after which login from console is possible, but telnet connection is not.
The error that is displayed is... (1 Reply)
Discussion started by: manoj_gopal
1 Replies
2. UNIX for Dummies Questions & Answers
Ok I am new to this and wondering if there is any way of connecting a cable modem to an SGI that is running IRIX 6.5 and how to do it... (1 Reply)
Discussion started by: Acidjack
1 Replies
3. Shell Programming and Scripting
I was wondering if anyone can help me out with a Solaris 9, FTP problem.
The problem is this. One of our scripts recently attempted to send files to a MS server, using FTP, and some error occurred. Because the script didn't trap for errors we didn't know about the problem until things started... (3 Replies)
Discussion started by: BCarlson
3 Replies
4. Solaris
Hi All,
I have installed Solaris 9 on on an AMD Opteron based server.
The server is rebooting after i perform the following:
- Logon to Solaris 9 AMD box through telnet or putty
- ftp to any other box suppose box A where the FTP server is running
- After logging in to the box A through... (1 Reply)
Discussion started by: jsvarma
1 Replies
5. Solaris
Hi ,
I faced a very strange problem when I unzip a zip file on my solaris workstation. Actually I wanted to transfer a folder, say it TEST which contains some sub-folders inside it from windows to solaris machine. So I zipped this folder to TEST.ZIP on my windows machine.
Then from my... (11 Replies)
Discussion started by: Raj Kumar Arora
11 Replies
6. Solaris
Hi,
I am unable to login into my terminal hosting Solaris 10 and get the below error message
"Server refused to allocate pty
ld.so.1: sh: fatal: libc.so.1: open failed: No such file or directory "
Is there anyways i can get into my machine and what kind of changes are required to be... (7 Replies)
Discussion started by: sankasu
7 Replies
7. Solaris
Hi all,
Previously I had both opensuse 11.3 and Windows XP SP2 on my PC, there was no problem at all.I was able to access all documents in Windows from opensuse.
Now when I wanted to install solaris 10 on the same machine there were 2 problems ...
1. Windows is not accessible from solaris... (3 Replies)
Discussion started by: M.Choudhury
3 Replies
8. Hardware
Hello,
I want to connect a VT520 terminal to p3 linux box.
I have two questions regarding the connection. First,
is it possible to use RJ45 instead of RS232
cable. (with DB9 pin to RJ45 and DB25 to RJ45 converter).
Second point is that; do i need null modem cable or
straight cable... (5 Replies)
Discussion started by: vectrum
5 Replies
9. UNIX for Advanced & Expert Users
Hi Am using unix Ksh
Am getting the problem while transferring zero size files through the script .
When i transfer zero size files from local machine to remote machine manually i can able to do it .
My question its beause of zero size files am not able to transfer through script ? or its... (2 Replies)
Discussion started by: Venkatesh1
2 Replies
10. Linux
Hi,
Could you please help me with the below issue..
I'm running RHEL6 OS on both server (192.168.0.10) and client machines (192.168.0.1).
I'm trying to connect to server from the client machine using ftp service.
I have installed vsftpd daemon on both the machines.
I'm getting... (4 Replies)
Discussion started by: raosr020
4 Replies
IE(4) BSD/i386 Kernel Interfaces Manual IE(4)
NAME
ie -- Ethernet device driver
SYNOPSIS
To compile this driver into the kernel, place the following line in your kernel configuration file:
device ie
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_ie_load="YES"
In /boot/device.hints:
hint.ie.0.at="isa"
hint.ie.0.port="0x300"
hint.ie.0.irq="5"
hint.ie.0.maddr="0xd0000"
HARDWARE
The ie driver provides supports the following 8 and 16bit ISA Ethernet cards that are based on the Intel i82586 chip:
o 3COM 3C507
o AT&T EN100
o AT&T Starlan 10
o AT&T Starlan Fiber
o Intel EtherExpress 16
o RACAL Interlan NI5210
DIAGNOSTICS
ie%d: unknown board type code %d An i82586 chip was found, but the driver was unable to determine the actual board type during the probe.
ie%d: kernel configured maddr %x doesn't match board configured maddr %x The device probe detected a different maddr than the one specified
in the kernel configuration file.
ie%d: can't find shared memory The device probe could not access the shared memory to determine its size.
ie%d: kernel configured msize %d doesn't match board configured msize %d The device probe found a different size for the shared memory than
the one specified in the kernel configuration file.
ie%d: kernel configured irq %d doesn't match board configured irq %d The device probe detected that the board is configured for a different
interrupt than the one specified in the kernel configuration file.
ie%d: reset The Intel i82586 had to be reset by the driver.
ie%d: transceiver problem The driver has detected a problem with the Ethernet transceiver. This is usually due to a loose or broken trans-
ceiver cable when using an external transceiver. When you experience this problem with an on-card transceiver your card may be incorrectly
jumpered for to use an external transceiver. Worst case your on-board transceiver may be broken.
ie%d: TDR detected an open %d clocks away The driver detected an open circuit in the Ethernet cable. Check your coax cable and terminator
resistors.
ie%d: TDR detected a short %d clocks away The driver detected a short circuit in the Ethernet cable. Check your coax cable and terminator
resistors.
ie%d: TDR returned unknown status %x The driver got an unknown status from the card during the Ethernet cable test.
ie%d: multicast address setup command failed The card could not be put into multicast mode.
ie%d: configure command failed The card refused to respond correctly during configuration.
ie%d: individual address setup command failed The programming of the Ethernet (MAC) address failed.
CAVEATS
The Racal Interlan NI5210 comes in variants with 8 and 16 kbytes of shared memory. It is strongly advisable to use the 16 kbyte variant.
You can upgrade your 8 kbyte card to 16 kbyte by adding an additional RAM chip.
SEE ALSO
arp(4), netintro(4), ng_ether(4), ifconfig(8)
AUTHORS
The ie device driver was written by Garrett A. Wollman, based on code by William F. Jolitz and Lawrence Berkeley Laboratories. 3C507 support
was written by Charles M. Hannum. This manual page was written by Wilko C. Bulte.
BSD
July 16, 2005 BSD