09-16-2008
The ALOM has its necessary parameters to be fine tuned
8 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Wath is this ??
eeE: WatchDog ReInitMemory 6 for board 0 WARNING: eeE: Allocb failure in ReInitMemory
Only renit manualy is a solution.
:confused:
Help me please
Tnks (2 Replies)
Discussion started by: RoMaGo
2 Replies
2. SCO
My Unix Server with SCO Unix ver 5, display Watchdog error which reads,
Watchdog ReInitMemory 6 for board 0 Warning : eeE : Allocb failure in ReInitMemory.
My server has 98 dumb terminals connected. It has 5 Hard Disks (SCSI) of 9.1 GB each and 512 MB RAM. Uses RAID level 5
After this error... (1 Reply)
Discussion started by: V.V.KUMAR
1 Replies
3. UNIX for Dummies Questions & Answers
How do you disable a server, #1, from trying to use the NIS that is running on another server, #2?
I would like the #1 server to just use the local etc/shadow file (3 Replies)
Discussion started by: calamine
3 Replies
4. Solaris
Hi,
is there something build in solaris that can act as "watchdog".
I have some process (service) running (e.g. Rhino). It can happen that if freezes totaly so I need to find this out and restart it totaly.
My vision is two possibilities.
1) there is some counter running and I will... (2 Replies)
Discussion started by: freeangel
2 Replies
5. Solaris
Hi,
Please let me know what is hardware watchdog enabled which we get when the solaris host is booting .As per my knowledge its the one states that the POST is enabled. correct me if am wrong. (1 Reply)
Discussion started by: rogerben
1 Replies
6. AIX
Hi All,
I am getting pages from EMS(Event Monitoring Servers) for "no watchdog notification"
I just wonder what cause this and what to look in the system.
this error was generated from production lpar which hosts p570
Thanks
Mann (4 Replies)
Discussion started by: chubby362002
4 Replies
7. Solaris
Hello everyone,
can anyone tell me how to disable sendmail on solaris 10?
I seem to have the sendmail process from hell. Did an SVCS | grep for mail and disabled the 2 processes it threw up. But something is still respawning sendmail (if I kill it manually) and it's doing the usual... (2 Replies)
Discussion started by: callmebob
2 Replies
8. Shell Programming and Scripting
Hi,
I am willing to build a script that does a "ps-ef" or "top" on a specific process, and if it finds it running to start another process.
Any suggestions to do this in a optimized way?
Thanks! (2 Replies)
Discussion started by: liviusbr
2 Replies
ICHWD(4) BSD Kernel Interfaces Manual ICHWD(4)
NAME
ichwd -- device driver for the Intel ICH watchdog interrupt timer
SYNOPSIS
To compile this driver into the kernel, place the following line in your kernel configuration file:
device ichwd
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
ichwd_load="YES"
DESCRIPTION
The ichwd driver provides watchdog(4) support for the watchdog interrupt timer present on all Intel ICH motherboard chipsets.
The ICH WDT counts down in ticks of approximately 0.6 seconds; the exact value depends on hardware quality and environmental factors. Sup-
ported watchdog intervals range from 2 to 63 ticks.
Note that on some ICH-based systems, the WDT may be present but disabled, either in hardware or by the BIOS. The ichwd driver attempts to
detect this condition and will refuse to attach if it believes the WDT is disabled.
SEE ALSO
watchdog(4), watchdog(8), watchdogd(8), watchdog(9)
Using the Intel ICH Family Watchdog Timer (WDT), Intel Application Note AP-725, Document Number 292273-001.
HISTORY
The ichwd driver first appeared in FreeBSD 5.3.
AUTHORS
The ichwd driver was written by Wm. Daryl Hawkins <dhawkins@tamu.edu> of Texas A&M University and Dag-Erling Smorgrav <des@FreeBSD.org>.
This manual page was written by Dag-Erling Smorgrav <des@FreeBSD.org>.
BSD
August 20, 2008 BSD