Sponsored Content
Full Discussion: Network Configuration
Operating Systems SCO Network Configuration Post 302236509 by andrewd on Monday 15th of September 2008 05:23:14 PM
Old 09-15-2008
Network Configuration

I have a SCO 5.07 Server and I am trying to get it on my network. I have edited the /etc/hosts file and /etc/rc2.d/s99route . I has connectivity on the NIC card but not sure if I am forgetting another file. Thanks!
 

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Network configuration in Solaris 8

Hi. I have installed Solaris 8 and I am trying to configure the network settings. For some reason every time I reboot, my card loses its configuration. I can run ifconfig and the only IP address bound to my card (on either interface) is 127.0.0.1. I can change that to a valid IP address on my... (8 Replies)
Discussion started by: Ask Me
8 Replies

2. IP Networking

Network Configuration for SunSparsh 5.8

Hi, I need to configure the Network for a Sun Solaris systems. The OS info is SunOS Sparsh 5.8 Generic_108528-13 Sun4u Sparc SUNW,Ultra-250. Please do let me know, how shall I shart with & more in configuring the Network. Below is the list of Network Configuration I need to Make ... (2 Replies)
Discussion started by: S.Vishwanath
2 Replies

3. HP-UX

HP-UX Network Configuration

Hi, I have installed a HP-UX B.11.00 U 9000/800 Server in one of the domain. And I'm also able to telnet/ping into this server from systems in the same domain. But I'm not able to telnet/ping into this server from a different domain. So, what shoud need to do to achieve this... (6 Replies)
Discussion started by: S.Vishwanath
6 Replies

4. Solaris

network configuration

hi again... i configured my network settings sometiime ago using the sys-unconfig command.the active link was rtls0. there was some problem with the network so i changed the ISP. now when im trying to reconfigure the system wit sys-unconfig, it tries to configure the network on rtls1 (and shows... (1 Reply)
Discussion started by: strider
1 Replies

5. Solaris

Specifying network configuration info

Can someone please point me in the correct direction of where I configure the network information on SunOS 5.8 server? (Searching SunSolve and Google have resulted in thousands of fixes for potential errors, but I can't find the general instructions, etc. for starting the process). Thanks! (2 Replies)
Discussion started by: FredSmith
2 Replies

6. UNIX for Dummies Questions & Answers

Network Configuration Commands.....

I need to know what commands I will need to use to change a host name, IP Address, and network configurations (routerings, dns, etc) and a Unix SCO machine. Also, if there is any short tutorials on using the commands, i would defiently like that information. Thanks!!! (1 Reply)
Discussion started by: HandleX
1 Replies

7. UNIX for Dummies Questions & Answers

network configuration

I am using solaris 10, my internet works alright but each time i reboot i keep loosing my connection. I will have to use the ifconfig iprb0 192.168.1.xx netmask 255.255.255.0 up and Route add default 192.168.1.xxx command to gain back my internet. I know there is a better way of addressing... (1 Reply)
Discussion started by: seyiisq
1 Replies

8. Solaris

Network configuration

Hi I have installed Solaris 5.10 on Intel x86 machine (standalone). I want to access internet through solaris. How should I configure the network? Is static IP or DHCP advisable? (5 Replies)
Discussion started by: johnl
5 Replies

9. Solaris

Problem in network configuration

Hi everybody, I have a very strange problem ; if somebody could help me it would be very kind. I'll try to explain my problem. I have 2 unix machines absolutely identical running solaris 9. For network reasons I need to change the IP address of the 2 machines. I proceed exactly the same on the... (11 Replies)
Discussion started by: aribault
11 Replies

10. UNIX for Advanced & Expert Users

network configuration on openbsd

Hi all, I got following configuration problem I need to configure tiny network on openbsd I got server1 with 3 interfaces vic0 em0 em1 The interface vic0 on server1 has follwoing IP 172.16.1.1 em0 firstly I would like to configure network under em0 (I have assigned to em0 following... (1 Reply)
Discussion started by: kvok
1 Replies
HOSTS(5)						      Debian GNU/Linux manual							  HOSTS(5)

NAME
hosts - The static table lookup for host names SYNOPSIS
/etc/hosts DESCRIPTION
This manual page describes the format of the /etc/hosts file. This file is a simple text file that associates IP addresses with hostnames, one line per IP address. For each host a single line should be present with the following information: IP_address canonical_hostname aliases Fields of the entry are separated by any number of blanks and/or tab characters. Text from a "#" character until the end of the line is a comment, and is ignored. Host names may contain only alphanumeric characters, minus signs ("-"), and periods ("."). They must begin with an alphabetic character and end with an alphanumeric character. Aliases provide for name changes, alternate spellings, shorter hostnames, or generic hostnames (for example, localhost). The format of the host table is described in RFC 952. The Berkeley Internet Name Domain (BIND) Server implements the Internet name server for UNIX systems. It augments or replaces the /etc/hosts file or host name lookup, and frees a host from relying on /etc/hosts being up to date and complete. In modern systems, even though the host table has been superseded by DNS, it is still widely used for: bootstrapping Most systems have a small host table containing the name and address information for important hosts on the local network. This is useful when DNS is not running, for example during system bootup. NIS Sites that use NIS use the host table as input to the NIS host database. Even though NIS can be used with DNS, most NIS sites still use the host table with an entry for all local hosts as a backup. isolated nodes Very small sites that are isolated from the network use the host table instead of DNS. If the local information rarely changes, and the network is not connected to the Internet, DNS offers little advantage. EXAMPLE
127.0.0.1 localhost 192.168.1.10 foo.mydomain.org foo 192.168.1.13 bar.mydomain.org bar 216.234.231.5 master.debian.org master 205.230.163.103 www.opensource.org HISTORICAL NOTE
Before the advent of DNS, the host table was the only way of resolving hostnames on the fledgling Internet. Indeed, this file could be cre- ated from the official host data base maintained at the Network Information Control Center (NIC), though local changes were often required to bring it up to date regarding unofficial aliases and/or unknown hosts. The NIC no longer maintains the hosts.txt files, though looking around at the time of writing (circa 2000), there are historical hosts.txt files on the WWW. I just found three, from 92, 94, and 95. FILES
/etc/hosts SEE ALSO
hostname(1) resolver(3), resolver(5), hosts(5), hostname(7), named(8), Internet RFC 952 AUTHOR
This manual page was written by Manoj Srivastava <srivasta@debian.org>, for the Debian GNU/Linux system. Debian 2002-06-16 HOSTS(5)
All times are GMT -4. The time now is 11:54 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy