Sponsored Content
Special Forums IP Networking To find switch port of machine running under VMware Post 302225579 by amsct on Friday 15th of August 2008 06:55:38 PM
Old 08-15-2008
If the interface of the vmware machine is bridged, you should be able to see it in the same way as any other physical machine. If your vm machine is using NAT to cross the host machine's physical interface, then it is the physical machine mac you should be looking for.
 

9 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

how to find out if a port is available on a remote machine?

hi, I can ping into another unix machine, but I cannot seem to access a certain application. I think it might be because I am now allowed to connect to the port (because of firewall configuration). How can I find out if I have access to a port on another machine? thanks (2 Replies)
Discussion started by: JamesByars
2 Replies

2. UNIX for Advanced & Expert Users

check remote switch port speed setting

Hi, Someone told me how to check the remote switch port's speed setting on the other end of the cable, from linux. I forgot it. Anyone knows? I checked dmesg, ethtool (haven't checked this out thoroughly) , no luck. thanks, Marc (1 Reply)
Discussion started by: marcpascual
1 Replies

3. AIX

Switch Port Becoming Private & restricting access

Hello folks, I have an AIX server that is connected to a storage array via a Brocade switch using 4 ports from either side. The zoning is done such that there are 4 paths visible from the server to the storage. My work involves frequent disabling or enabling the switch ports that are... (1 Reply)
Discussion started by: nkiran
1 Replies

4. UNIX for Advanced & Expert Users

How to Switch off a Unix machine abruptly

Hi Folks, My UNIX machine is placed geographically in another location. I have a remote access towards it. I want to abruptly switch off my unix machine through remote connection. Is it possible through any UNIX commands? I practically want to power off a PC , something like unplugging a power... (12 Replies)
Discussion started by: gjasper
12 Replies

5. Virtualization and Cloud Computing

solaris virtual machine vmware esx

Hi All How would you send a solaris virtual machine in vmware esx, a break signal? :confused: (0 Replies)
Discussion started by: jakerock
0 Replies

6. Solaris

How to find port number wwn of particular port on dual port HBA,?

please find the below o/p for your reference bash-3.00# fcinfo hba-port HBA Port WWN: 21000024ff295a34 OS Device Name: /dev/cfg/c2 Manufacturer: QLogic Corp. Model: 375-3356-02 Firmware Version: 05.03.02 FCode/BIOS Version: BIOS: 2.02; fcode: 2.01;... (3 Replies)
Discussion started by: sb200
3 Replies

7. Linux

Connect from USB to serial port of switch

I have someone wanting to connect to the serial management port of a switch from a PC running CentOS6. The management port on the switch is apparently baud 9600, 8 data bits, 1 stop bit & no parity They have plugged in a cable to connect and the output from lsusb is:-Bus 001 Device 001: ID... (7 Replies)
Discussion started by: rbatte1
7 Replies

8. UNIX for Beginners Questions & Answers

How to check everything are migrated after the physical to vmware virtual machine?

I have a physical machine , just use vmware tools migrated data to virtual machine . how can I check these two servers - old and new server , the data are the same , all files are copy to new server ? thanks (2 Replies)
Discussion started by: ust3
2 Replies

9. UNIX for Beginners Questions & Answers

How to find whether Solaris installed on physical machine or on a VMware/KVM?

Hi All, . I am trying to find whether Solaris 11 installed on physical server or on VMware/KVM. I tried uname -a but it's giving only whether i installed on X86 or sparc machine. I tried prtdiag command but it's giving below information. command : prtdiag -v |grep "System... (2 Replies)
Discussion started by: sravani25
2 Replies
SYSTEMD-MACHINE-ID-COMMIT.SERVICE(8)			 systemd-machine-id-commit.service		      SYSTEMD-MACHINE-ID-COMMIT.SERVICE(8)

NAME
systemd-machine-id-commit.service - Commit a transient machine ID to disk SYNOPSIS
systemd-machine-id-commit.service DESCRIPTION
systemd-machine-id-commit.service is an early boot service responsible for committing transient /etc/machine-id files to a writable disk file system. See machine-id(5) for more information about machine IDs. This service is started after local-fs.target in case /etc/machine-id is a mount point of its own (usually from a memory file system such as "tmpfs") and /etc is writable. The service will invoke systemd-machine-id-setup --commit, which writes the current transient machine ID to disk and unmount the /etc/machine-id file in a race-free manner to ensure that file is always valid and accessible for other processes. See systemd-machine-id-setup(1) for details. The main use case of this service are systems where /etc/machine-id is read-only and initially not initialized. In this case, the system manager will generate a transient machine ID file on a memory file system, and mount it over /etc/machine-id, during the early boot phase. This service is then invoked in a later boot phase, as soon as /etc has been remounted writable and the ID may thus be committed to disk to make it permanent. SEE ALSO
systemd(1), systemd-machine-id-setup(1), machine-id(5), systemd-firstboot(1) systemd 237 SYSTEMD-MACHINE-ID-COMMIT.SERVICE(8)
All times are GMT -4. The time now is 09:40 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy