08-11-2008
That won't fit on a floppy. Could I write that to CD?
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
ok -- i've got the main install done, but when it goes to set up apt, i can't get to an http or ftp server to get the packages. seems my dns isn't working. problem is -- i have no way, or at least don't know a way, to get into any sort of gui, in which i think i could get it going myself. i'm stuck... (1 Reply)
Discussion started by: aenemated
1 Replies
2. Debian
I've recently installed the Sarge version of Debian Linux and have run into a problem with it's networking abilities.
I access the internet by cable modem, connected to a linksys broadband router. The router is set up to allow full access to this computer.
When I run dhclient from Debian, it... (0 Replies)
Discussion started by: Losie
0 Replies
3. UNIX for Dummies Questions & Answers
Hi All,
I am unable to find the command for knowing the RAM size on debian os.
Also i am unable to use the command shutdown on command line. it asks for the following options:
cloud9:~# shutdown
Usage: shutdown time
-a: use /etc/shutdown.allow
... (6 Replies)
Discussion started by: gauri
6 Replies
4. UNIX for Advanced & Expert Users
Hi all,
I've a debian 4 etch machine which runs on a HP Proliant G5 server. My server became too slow yesterday. I restarted the it and also try to run in Run Level 1 but nothing changed. This is the status of my debian box:
top - 12:33:11 up 34 min, 3 users, load average: 0.00, 0.03, 0.21... (2 Replies)
Discussion started by: mjdousti
2 Replies
5. Debian
Hey, I recently installed Debian on a desktop PC but when it starts I can't see anything (the monitor say no signal). I don't have any idea or even a way to figure out what going on here since I can't see anything at all not even the console. Is there something that I missed in the install, or is... (22 Replies)
Discussion started by: neur0n
22 Replies
6. UNIX for Dummies Questions & Answers
Hello,
Lately installed vnc4server on debian, however it listens only to ipv6,
how is it possible to force vnc4server to listen both ipv4 and ipv6 ?
the cat /proc/sys/net/ipv6/bindv6only returns 0
debian stable 6.0.1
thanks. (2 Replies)
Discussion started by: hachik
2 Replies
7. Debian
Hello,
Anyone already tried to install Debian Sparc in a Sun V880 ?! I'm trying to and after I boot it with the CDROM the system starts to boot up and I don't see any errors message but it freezes after it detects the USB ports (There is nothing attached to it and I don't use it).
Here is a... (8 Replies)
Discussion started by: pxb368@motorola
8 Replies
8. Debian
I installed Debian 8.1:cool: with Xubuntu as dual boot :D...
During installation of Debian 8.1 i skipped user account creation :confused: ...now i can't login to Debian 8.1 :(:eek: ..help... (1 Reply)
Discussion started by: Zorion10
1 Replies
9. Debian
Hello,
I need to upgrade my Debian system 7.8 to 8.5 but by default via apt-get It moves to 8.6 version(latest stable version). I'm new to Debian so didn't figure out the solution.
I've checked few suggestions over internet like editing apt source list file using snapshot archive.
Please... (2 Replies)
Discussion started by: Mannu2525
2 Replies
FD(4) Kernel Interfaces Manual FD(4)
NAME
fd - floppy disk
DESCRIPTION
The fd* devices refer to the Floppy disk driver using the NEC PD765 floppy disk controller. These diskettes are arrays of 512 byte sec-
tors, although Minix always works with two sectors at a time due to its 1024 byte block size. You can read or write any number of bytes
however, Minix takes care of cutting and pasting incomplete blocks together.
The driver is normally configured for two floppy disk devices fd0 and fd1. It can handle two more, but it is unlikely that the average PC
can.
On the first access to an fd device (by open(2) or mount(2)), the driver will execute a series of read tests to determine the floppy type.
This works ok for all floppy types except the true 360k type, because it is indistinguishable from the 720k type. This only means that the
size of the floppy is not estimated right.
Bits 2-6 of the minor device number may be set to the floppy disk type to make it known to the driver what type of diskette it is reading
or writing. The non-auto devices should be used for formatting, or when one wants to be absolutely sure that the device is accessed right.
These devices exist for drive 0:
type device minor media
0 fd0 0 autodetect
1 pc0 4 360k, 5.25"
2 at0 8 1.2M, 5.25"
3 qd0 12 360k in a 720k, 5.25" drive
4 ps0 16 720k, 3.5"
5 pat0 20 360k in a 1.2M, 5.25" drive
6 qh0 24 720k in a 1.2M, 5.25" drive
7 PS0 28 1.44M, 3.5"
Type 4 may also be used for the rarely seen 720k, 5.25" floppies (type 2 made them obsolete fast.) Note that these "types" only describe
the floppies from a software point of view, type 1 and 4 drives use the same parameters.
If the format bit (bit 7) is set, then the driver interprets write commands as track formatting requests. This is used by the format(1)
command.
If the type bits are set to 28, 29, 30, or 31, then the driver uses a partition table found in sector 0 to partition the floppy. The par-
titions of fd0 may be accessed as fd0a through fd0d. See hd(4) for a description of the partition table, and associated ioctl commands.
FILES
/dev/fd[0-3], /dev/pc[0-3], /dev/at[0-3], /dev/qd[0-3], /dev/ps[0-3], /dev/pat[0-3], /dev/qh[0-3], /dev/PS[0-3], /dev/fd[0-3][a-d]
SEE ALSO
format(1), hd(4), part(8).
BUGS
The driver does not know the size of a 360k diskette in a 360k 5.25" drive, because it uses the 720k parameters for it. So it will happily
try to read past the end making all kinds of interesting noises. It's a good thing these drives are practically obsolete.
The partition table is only read when the drive motor is off and only for an auto or partition device. The driver assumes that a floppy in
a drive with a running motor can't have been replaced all of a sudden.
AUTHOR
Kees J. Bot (kjb@cs.vu.nl)
FD(4)