08-07-2008
Do you have the netapp host services running on the Solaris server or are you just mounting over the network??
9 More Discussions You Might Find Interesting
1. Solaris
Hi,
I'm connecting a Solaris 10 server to a Netapp filer with two single port Emulex (Sun StorageTek PCI-X Enterprise 4GB FC HBA) HBAs. After physically installing both these HBAs what do I ned to do within Solaris 10 to enable them and configure them with persistent bindings.
Do I need... (6 Replies)
Discussion started by: gwhelan
6 Replies
2. Solaris
Hi,
I've just edited this post. I found the solution for this. Thanks. (0 Replies)
Discussion started by: gwhelan
0 Replies
3. AIX
Anyone know how to resize a LUN (if SAN disk array has increased the LUN size) and have AIX LVM know about it? Or is it automatic?
Equivalent vxvm command is something like: vxdisk resize size= (3 Replies)
Discussion started by: apra143
3 Replies
4. AIX
Good afternoon!
Help with a solution
I have AIX 7.1
works through vios
I expanded Lun
that it is necessary to make that aix saw this change and to expand the section lvm
Sorry for my English (1 Reply)
Discussion started by: iformats
1 Replies
5. AIX
Hi,
I have aix 6.1 box. I want to configure iscsi luns from netapp storage. I tried in google but not getting proper solution for that. i m not getting the proper iqn name.
Please share me the steps to complete this requirements.
Thanks in advance. (1 Reply)
Discussion started by: sunnybee
1 Replies
6. Red Hat
Is it possible to resize a filesystem by resizing the LUN on RHEL 6.4 64-bit with LVM and no impact to running applications? The research I have done so far seems to take the approach of adding a new LUN and then expaning the volume group to the new LUN. I'm looking for an approach that avoids a... (7 Replies)
Discussion started by: aenagy
7 Replies
7. Solaris
What command can I use to find out details about a netapp filer.
I have a directory that is a filer i would like to know details about the source host/folder that it points to.
Thanks. (2 Replies)
Discussion started by: jjohnson
2 Replies
8. Solaris
So,
We have a Netapp storage solution. We have Sparc T4-4s running with LDOMS and client zones in the LDOMS, We are using FC for storage comms. So here's the basic setup
FC luns are exported to the primary on the Sparc box. using LDM they are then exported to the LDOM using vdisk. at the... (4 Replies)
Discussion started by: os2mac
4 Replies
9. Linux
Hi
I need to identify a newly attached LUN from NetApp on a linuxserver running uname -o
GNU/Linux
I have first run the df -h and got the following:
df -h
Filesystem Size Used Avail Use% Mounted on
/dev/mapper/vg_outsystemdb-lv_root
50G 2.7G 45G ... (3 Replies)
Discussion started by: fretagi
3 Replies
ypset(1M) System Administration Commands ypset(1M)
NAME
ypset - point ypbind at a particular server
SYNOPSIS
/usr/sbin/ypset [-d ypdomain] [-h host] server
DESCRIPTION
In order to run ypset, ypbind must be initiated with the -ypset or -ypsetme options. See ypbind(1M). ypset tells ypbind to get NIS services
for the specified ypdomain from the ypserv process running on server. If server is down, or is not running ypserv, this might not be dis-
covered until an NIS client process tries to obtain a binding for the domain. At this point, the binding set by ypset is tested by ypbind.
If the binding is invalid, ypbind attempts to rebind for the same domain.
ypset is useful for binding a client node that is not on a broadcast net, or is on a broadcast net that is not running an NIS server host.
It is also useful for debugging NIS client applications, for instance, where an NIS map exists only at a single NIS server host.
Where several hosts on the local net are supplying NIS services, ypbind can rebind to another host, even while you attempt to find out if
the ypset operation succeeded. For example, if you enter the ypset command below, you might get the subsequent response from ypwhich:
example% ypset host1
example% ypwhich
host2
The sequence shown above is a function of the NIS subsystem's attempt to load-balance among the available NIS servers, and occurs when
host1 does not respond to ypbind because it is not running ypserv (or is overloaded), and host2, running ypserv, obtains the binding.
server indicates which NIS server to bind to, and must be specified as a name or an IP address. This works only if the node has a current
valid binding for the domain in question and ypbind has been set to allow use of ypset. In most cases, server should be specified as an IP
address.
ypset tries to bind over a connectionless transport. The NIS library call, yp_all(), uses connection-oriented transport and derives the
NIS server's address based on the connectionless address supplied by ypset.
Refer to ypfiles(4) for an overview of the NIS name service.
OPTIONS
-d ypdomain Use ypdomain, instead of the default domain.
-h host Set ypbind's binding on host, instead of locally. Specify host as a name.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWnisu |
+-----------------------------+-----------------------------+
SEE ALSO
ypwhich(1), ypfiles(4), attributes(5)
SunOS 5.10 14 Sep 1992 ypset(1M)