Hi,
I am trying to remove duplicate lines from a file. For example the contents of example.txt is:
this is a test
2342
this is a test
34343
this is a test
43434
and i want to remove the "this is a test" lines only and end up with the numbers in the file, that is, end up with:
2342... (4 Replies)
Hi
i have the below lines from a file
7538
PRGRP450800PERSONAL SOAP AND BATH ADDITIV 7036
PRGRP450800PERSONAL SOAP AND BATH ADDITIV 7036
PRGRP450800PERSONAL SOAP AND BATH ADDITIV 7036... (3 Replies)
Hi,
I need to concatenate three files in to one destination file.In this if some duplicate data occurs it should be deleted.
eg:
file1:
-----
data1 value1
data2 value2
data3 value3
file2:
-----
data1 value1
data4 value4
data5 value5
file3:
-----
data1 value1
data4 value4 (3 Replies)
Hi Guru's , I have a whole bunch of files in /var/tmp that i need to strip any blank lines from, so ive written the following script to identify the lines (which works perfectly).. but i wanted to know, how can I actually strip the identified lines from the actual source files ??
my... (11 Replies)
Hello,
I am in need of removing duplicate lines from within a file per section.
File:
ABC1 012345 header
ABC2 7890-000
ABC3 012345 Header Table
ABC4
ABC5 593.0000 587.4800
ABC5 593.5000 587.6580 <= dup need to remove
ABC5 593.5000 ... (5 Replies)
In my bash script I want to echo lines in a file and ensure no blank lines are echoed:for i in $(cat txt)
do
echo $i | sed 's/|/ /g;s/ SEARCHTERM$//g;s/ /\r\n/g;s/^$/d'
done
Keep in mind this is a fragment so ignore the fact that the for loop is not closed. When I add the "s/^$/d' per... (12 Replies)
Hi All,
How do i remove continuos blank lines from a file.
I have a file with data:
abc;
def;
ghi;
jkl;
mno;
pqr;
In the above file, there are two blank lines. I want to remove, one out of them.
My output should look like: (2 Replies)
Hi,
my input file is like this I want to remove the blank line.
"/home/rit/sandbox/garuda/data/test/woman/T_RITK_F0008_ML_100080039.lab"
r
a
N
e
l
a
k
sh
a
m
.
"/home/rit/sandbox/garuda/data/test/woman/T_RITK_F0008_ML_100070453.lab"
a
v
a
s (4 Replies)
Discussion started by: sreejithalokkan
4 Replies
LEARN ABOUT SUSE
irsend
IRSEND(1) FSF IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.8.7pre1 May 2010 IRSEND(1)