I don't think you need "modprobe", instead, you have to mount the NTFS drive, as in :
, certainly, replace the respective parameters, have a look here or here.
Hi All,
Is there a max number of slabs that can be used per kernel module? I'm having a tough time finding out that kind of information, but the array 'node_zonelists' (mmzone.h) has a size of 5. I just want to avoid buffer overruns and other bad stuff.
Cheers,
Brendan (4 Replies)
Hi All,
I've seen people build modules against a certain kernel source (eg in /usr/src/kernels/my_source/) and some people build against the sources in /lib/modules/my_source/build/
What is the difference and are there any benefits to using the /lib/modules source?
Regards,
Brendan (0 Replies)
Hi all,
I am working on USB data monitoring on Fedora Core 9. Kernel 2.6.25 has a built-in module (the one that isn't loadable, but compiles and links statically with the kernel during compilation) to snoop USB data. It is in <kernel_source_code>/drivers/usb/mon/.
I need to know if I can... (0 Replies)
Hi masters,
I am new to linux and unix forum and this is my first forum. So please excuse if
I am not giving sufficient information. I will give them on request.
I have created a bandwidth manager module. I am using a 2.6.9 kernel and in Red Hat 3.4.3 distribution. But when i run make... (1 Reply)
Hi All,
I need to develop a kernel module which changes the IP address of a package according to its mac address. It would be a sort of L2 Nat.
Somebody know if I can do this using netfilter??
Thanks. (2 Replies)
I have one big module 2.6.18 kernel mod.c
I want to divide this to several files.
The problem is to write right Makefile
lib1.h
lib1.c
mod.c
mod.c works fine normally but when I divide into several files
and try to compile with this makefile
obj-m := mod.o
mod-objs := lib1.o
... (3 Replies)
Hi,
if I install a module with specific parameter, will this parameters applied next time system boots?
for exampe, I want to disable InterruptThrottleRate
modprobe e1000e InterruptThrottleRate=0
Is this parameter apllied only for this run, or this module will always use this parameter when... (2 Replies)
Question may seem illogical but I still need clarification.
Can we debug kernel modules loaded on my target system using kdb / kgdb without using any other system or remote debugging?
In other words my question is can we use kdb/kgdb to debug kernel modules running on same system? (2 Replies)
Hi everyone,
I am trying to prevent the ehci_hcd kernel module to load at boot time.
Here's what I've tried so far:
1) Add the following line to /etc/modprobe.d/blacklist.conf (as suggested here):
2) Blacklisted the module by adding the following string to
3) Tried to blacklist the module... (0 Replies)
Discussion started by: gacanepa
0 Replies
LEARN ABOUT DEBIAN
scrounge-ntfs
scrounge-ntfs(8) BSD System Manager's Manual scrounge-ntfs(8)NAME
scrounge-ntfs -- helps retrieve data from corrupted NTFS partitions
SYNOPSIS
scrounge-ntfs -l disk
scrounge-ntfs -s disk
scrounge-ntfs [-m mftoffset] [-c clustersize] [-o outdir] disk start end
DESCRIPTION
scrounge-ntfs is a utility that can rescue data from corrupted NTFS partitions. It writes the files retrieved to another working file system.
Certain information about the partition needs to be known in advance.
The -l mode is meant to be run in advance of the data corruption, with the output stored away in a file. This allows scrounge-ntfs to recover
data reliably. See the 'NOTES' section below for recover info when this isn't the case.
OPTIONS
The options are as follows:
-c The cluster size (in sectors). When not specified a default of 8 is used.
-l List partition information for a drive. This will only work when the partition table for the given drive is intact.
-m When recovering data this specifies the location of the MFT from the beginning of the partition (in sectors). If not specified
then no directory information can be used, that is, all rescued files will be written to the same directory.
-o Directory to put rescued files in. If not specified then files will be placed in the current directory.
-s Search disk for partition information. (Not implemented yet).
disk The raw device used to access the disk which contains the NTFS partition to rescue files from. eg: '/dev/hdc'
start The beginning of the NTFS partition (in sectors).
end The end of the NTFS partition (in sectors)
NOTES
If you plan on using this program sucessfully you should prepare in advance by storing a copy of the partition information. Use the -l option
to do this. Eventually searching for disk partition information will be implemented, which will solve this problem.
When only one partition exists on a disk or you want to rescue the first partition there are ways to guess at the sector sizes and MFT loca-
tion. See the scrounge-ntfs web page for more info:
http://memberwebs.com/swalter/software/scrounge/
AUTHOR
Stef Walter <stef@memberwebs.com>
scrounge-ntfs June 1, 2019 scrounge-ntfs