07-25-2008
hmmm... i don't know why the disk doesn't accept the label... try to call "format -e" and choose "label" (the right disk!) and then take the "smi" label...
10 More Discussions You Might Find Interesting
1. Linux
Hi everyone,
OK, I've made a monumental fsck-up of my linux installation AND I did not backup my data properly (idiot!), so I'm really up the proverbial without a paddle here.
Basically the problem is I re-sized my /home partition (hda13) using Partition Magic 8.0, after doing so my mandrake... (0 Replies)
Discussion started by: alarmcall
0 Replies
2. Solaris
I just was given an Ultra 60 that I'm trying to get started so that I can re-load the system with Solaris 10. I can't seem to get the system to boot past the initial memory check. I've tried to do an Stop-A to get to the eeprom, but can't do that. My next step is to try to send a break from the... (0 Replies)
Discussion started by: zosojohnny
0 Replies
3. Solaris
Hi Fellows,
I am trying to mirror 2 identical disks on a SUN Ultra 10 machines (with new installation of Solaris 8). In the process, I found 2 issues:
1. prtvtoc /dev/rdsk/c0t0d0s0 | fmthard -s - /dev/rdsk/c0t1d0s0
Result: Disk partitions between the 2 disks do not match up.
2. manually... (2 Replies)
Discussion started by: o51974
2 Replies
4. Solaris
Hi,
I have a Sun X4200, when I try to reboot the machine it's not detecting the drive and it shows the following error when I try to rebuilt it. I am not sure whether its a bad HD or something else.
Label says 983040 blocks: Drive says 983039 blocks
WARNING:... (1 Reply)
Discussion started by: gunnervarma
1 Replies
5. Solaris
I have created 1 LUN.
1)LUN 00BB 200GB /dev/rdsk/c1t3d44
/dev/rdsk/c2t28d44
/dev/rdsk/c3t19d44
/dev/rdsk/c4t12d44
2) Already added the new entry into sd.conf and rebooted.
3) Already done these:
powercf –q
power config
4) power display dev=all
I can see the new Symmetrix device.... (1 Reply)
Discussion started by: sirius20d
1 Replies
6. UNIX for Advanced & Expert Users
We have an issue here:
The libc.so.6 file (link) is corrupted and it causes the system unbootable. It even doesn't boot to single user mode. How can we boot the system to fix the library file? Or is there any other solutions for this issue?
Here are some boot messages:... (6 Replies)
Discussion started by: aixlover
6 Replies
7. Filesystems, Disks and Memory
I've seen several posts that are similar to what I'm trying to do but no dice. I have a server (SunFire V215) that went belly up. I've set up a new one. I'm getting a corrupt label: wrong magic number error. Everything I'm seeing says label the drives, but if I do I'm afraid I'll lose the data... (0 Replies)
Discussion started by: tnelson
0 Replies
8. Emergency UNIX and Linux Support
Need help/advice urgently.:wall:
I really shot myself in the foot this time. Here is the scenario
Have a Solaris server Solaris 10 x86 Update 8.
Installed an LSI MegaRaid 9280 raid controller and attached a 16 bay JBOD box to it, created a RAID6 virtual drive with 1 hot spare.
Created a... (2 Replies)
Discussion started by: ccj4467
2 Replies
9. Solaris
I am trying to get an old Ultra 45 to boot and it is stuck in a loop. I cannot get anything to come up on a monitor, so when I hook up a serial connection to the TTYa interface I see the following output:
@(#)OBP 4.21.2 2005/12/22 17:17 Sun Ultra 45 Workstation
Clearing TLBs
Loading... (0 Replies)
Discussion started by: Madrox72
0 Replies
10. Solaris
Hi all,
I've just replaced the eprom battery on my Sun Ultra-30 and having boot issues. For some reason its trying to boot off the network instead of the DISK1. Howe can I change it so the open boot does not default to the boot device: NET
Thanks,
Rob (3 Replies)
Discussion started by: robbo007
3 Replies
LEARN ABOUT CENTOS
mkqdisk
mkqdisk(8) Quorum Disk Management mkqdisk(8)
NAME
mkqdisk - Cluster Quorum Disk Utility
WARNING
Use of this command can cause the cluster to malfunction.
SYNOPSIS
mkqdisk [-?|-h] | [-L] | [-f label] [-c device -l label] [-d [-d ...]]
DESCRIPTION
The mkqdisk command is used to create a new quorum disk or display existing quorum disks accessible from a given cluster node.
OPTIONS
-c device -l label
Initialize a new cluster quorum disk. This will destroy all data on the given device. If a cluster is currently using that device
as a quorum disk, the entire cluster will malfunction. Do not run this on an active cluster when qdiskd is running. Only one
device on the SAN should ever have the given label; using multiple different devices is currently not supported (it is expected a
RAID array is used for quorum disk redundancy). The label can be any textual string up to 127 characters - and is therefore enough
space to hold a UUID created with uuidgen(1).
-f label
Find the cluster quorum disk with the given label and display information about it.
-L Display information on all accessible cluster quorum disks.
-d Increase debugging level. Specify multiple times for more information. Currently, specifying more than twice has no effect.
SEE ALSO
qdisk(5), qdiskd(8), uuidgen(1)
July 2006 mkqdisk(8)