Sponsored Content
Full Discussion: How to check the LAN card?
Operating Systems Linux How to check the LAN card? Post 302218155 by mark54g on Thursday 24th of July 2008 02:08:43 PM
Old 07-24-2008
 

10 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

LAN Card Problem !

The Lan card in one of our UIII WS's seem doesn't work,so with ping command i can not see any of the machines in LAN and with some other tests i'm sure it's not OK. I tried to use the second card on PCI port ,but the replaced card was one of the ordinary card for PC's ...by the way after... (1 Reply)
Discussion started by: nikk
1 Replies

2. UNIX for Dummies Questions & Answers

how to check if sound card exists?

hi, i have a sun sparc II machine. i would like to play music from this workstation. so how should i check whether my machine has a sound card installed? what command should i type? pls enlighten me. thanks (1 Reply)
Discussion started by: champion
1 Replies

3. Cybersecurity

lan card autonegotiation?

what is lan card autonegotiation ? how to enable and disable this feature? (2 Replies)
Discussion started by: nabil_boussetta
2 Replies

4. SCO

LAN card problem

Dear all Im facing one problem in SCO 5.0.5 , its that in the server there are three LAN cards INTEL PRO 100 series but when we configure all the three cards then LAN stops working . self ping is possible but no one can ping the server. If we remove driver of any one card LAN starts working. Is... (1 Reply)
Discussion started by: ccvyas
1 Replies

5. Solaris

Does x86 solaris 9 support PCI RealTek Lan Card

Hi, i have a RealTek Lan Card on my machine. Does Solaris 9 supports this lan card . Thank You, Shafi (3 Replies)
Discussion started by: sol8admin
3 Replies

6. SCO

lan card not detecting

hi all i have installed SCO 5.0.5 on a "Netfinity 5000" IBM server. But the OS is not detecting the lan card. how can i detect it.... help and thanks in advance . bidhayak (3 Replies)
Discussion started by: bidhayakm
3 Replies

7. Programming

LAN card status Information

Please tell me API in Solaris / Linux / UNIX to get status information of LAN card. (1 Reply)
Discussion started by: mansoorulhaq
1 Replies

8. Solaris

Can't ping new PCI LAN card x4270_m2

Hi, I've recently moved my pci LAN card from Slot2 Slot5 on my sun x4270_m2 server (solaris 10). I've done the touch / reconfigure and devfsadm, however my issue is that im able to configure the e1000g7 port with an ip address (192.168.0.1) but if i plug my laptop (set with static ip... (7 Replies)
Discussion started by: kerrygold
7 Replies

9. Linux

Lan card not reaching Gateway

Hi, I have this problem on RHEL box. I am using two NIC's of same model and make (Intel 82557) in the adjacent PCI slots . I am using each one for different subnet and have assigned them ipaddresses and gateways of respective subnets . While one is O.K. connecting to its ... (5 Replies)
Discussion started by: dextergenious
5 Replies

10. Red Hat

PC cannot reach two lan card Linux box

we have red hat 6 linux box There are two lan card one lan card eth0 have ip 10.82.190.31/24 GW 10.82.190.254 2th lan card eth1 have ip 10.82.188.33/24 GW 10.82.188.254 I have below route ... I use two route table root@xxx# netstat -rn Kernel IP routing table Destination Gateway ... (5 Replies)
Discussion started by: chuikingman
5 Replies
veth(4) 						     Linux Programmer's Manual							   veth(4)

NAME
veth - Virtual Ethernet Device DESCRIPTION
The veth devices are virtual Ethernet devices. They can act as tunnels between network namespaces to create a bridge to a physical network device in another namespace, but can also be used as standalone network devices. veth devices are always created in interconnected pairs. A pair can be created using the command: # ip link add <p1-name> type veth peer name <p2-name> In the above, p1-name and p2-name are the names assigned to the two connected end points. Packets transmitted on one device in the pair are immediately received on the other device. When either devices is down the link state of the pair is down. veth device pairs are useful for combining the network facilities of the kernel together in interesting ways. A particularly interesting use case is to place one end of a veth pair in one network namespace and the other end in another network namespace, thus allowing communi- cation between network namespaces. To do this, one first creates the veth device as above and then moves one side of the pair to the other namespace: # ip link set <p2-name> netns <p2-namespace> ethtool(8) can be used to find the peer of a veth network interface, using commands something like: # ip link add ve_A type veth peer name ve_B # Create veth pair # ethtool -S ve_A # Discover interface index of peer NIC statistics: peer_ifindex: 16 # ip link | grep '^16:' # Look up interface 16: ve_B@ve_A: <BROADCAST,MULTICAST,M-DOWN> mtu 1500 qdisc ... SEE ALSO
clone(2), network_namespaces(7), ip(8), ip-link(8), ip-netns(8) COLOPHON
This page is part of release 4.15 of the Linux man-pages project. A description of the project, information about reporting bugs, and the latest version of this page, can be found at https://www.kernel.org/doc/man-pages/. Linux 2018-02-02 veth(4)
All times are GMT -4. The time now is 03:46 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy