07-24-2008
Thanks for answering but my question was really aimed to the OP.
7 More Discussions You Might Find Interesting
1. Solaris
HI All,
I have three solaris disks: disk 1 & 2 and "image" disk.
However, no instructions for installation on x86 came with them. (I downloaded from SUN.)
I've searched far and wide on the net trying to find instructions for installing Solaris on my PII 500 mhz intel machine, but have... (7 Replies)
Discussion started by: JaredsNew
7 Replies
2. UNIX for Dummies Questions & Answers
I am trying to figure out a way to install drivers for a network card. I have a 3C905C-TXM 3Com card that appeared to check out on Solaris's Web Site. I found what I thought was a driver, although that may not be the case, because the instructions asked me to copy-and-paste the contents into a... (1 Reply)
Discussion started by: Jody
1 Replies
3. UNIX for Dummies Questions & Answers
How can I install Solaris 10 x86 on a machine without a DVD drive? Is there a way to boot from a flash stick or install it through a network? Any help will be appreciated. (1 Reply)
Discussion started by: Bradj47
1 Replies
4. Solaris
Hi everyone,
Normally it always easier in Sparc machine, i can set or manually use the boot-device in NVram to boot the mirrored disk. However I have a big trouble about x86 mirror for a long time. I have been doing anything i can: search document, google, ask the others.
Recently i did as... (5 Replies)
Discussion started by: tien86
5 Replies
5. Solaris
I am trying to install apache on a sun server (Solaris 10 x86) but when I execute the compile i have the following error;
configure failed for srclib/apr
Can anybody help with this.
Thanks for the usual help
oh-daa (2 Replies)
Discussion started by: oh-daa
2 Replies
6. UNIX for Beginners Questions & Answers
Unix Buddies
Burned download to DVD-R.
Booted it.
It dropped me at a command line.
Is it working properly?
Thanks! (7 Replies)
Discussion started by: Solaris User
7 Replies
7. Solaris
I've installed Slack 14.2 on /dev/sda1 (/dev/sda2 is swap) and FreeBSD 12 on /dev/sda3 and lilo is the boot manager.
FreeBSD slices are as follows;
/ on /dev/ada0S3a, swap on /dev/ada0s3e, /var on /dev/ada0s3b, /tmp on /dev/ada0s3d and /usr on /dev/ada0s3f.
I hesitate to install Solaris 10... (2 Replies)
Discussion started by: vectrum
2 Replies
LEARN ABOUT DEBIAN
debconf-set-selections
DEBCONF-SET-SELECTIONS(1) Debconf DEBCONF-SET-SELECTIONS(1)
NAME
debconf-set-selections - insert new default values into the debconf database
SYNOPSIS
debconf-set-selections file
debconf-get-selections | ssh newhost debconf-set-selections
DESCRIPTION
debconf-set-selections can be used to pre-seed the debconf database with answers, or to change answers in the database. Each question will
be marked as seen to prevent debconf from asking the question interactively.
Reads from a file if a filename is given, otherwise from stdin.
WARNING
Only use this command to seed debconf values for packages that will be or are installed. Otherwise you can end up with values in the
database for uninstalled packages that will not go away, or with worse problems involving shared values. It is recommended that this only
be used to seed the database if the originating machine has an identical install.
DATA FORMAT
The data is a series of lines. Lines beginning with a # character are comments. Blank lines are ignored. All other lines set the value of
one question, and should contain four values, each separated by one character of whitespace. The first value is the name of the package
that owns the question. The second is the name of the question, the third value is the type of this question, and the fourth value (through
the end of the line) is the value to use for the answer of the question.
Alternatively, the third value can be "seen"; then the preseed line only controls whether the question is marked as seen in debconf's
database. Note that preseeding a question's value defaults to marking that question as seen, so to override the default value without
marking a question seen, you need two lines.
Lines can be continued to the next line by ending them with a "" character.
EXAMPLES
# Force debconf priority to critical.
debconf debconf/priority select critical
# Override default frontend to readline, but allow user to select.
debconf debconf/frontend select readline
debconf debconf/frontend seen false
OPTIONS
--verbose, -v
verbose output
--checkonly, -c
only check the input file format, do not save changes to database
SEE ALSO
debconf-get-selections(1) (available in the debconf-utils package)
AUTHOR
Petter Reinholdtsen <pere@hungry.com>
2012-09-10 DEBCONF-SET-SELECTIONS(1)