|
|
Sponsored Content
Operating Systems
Solaris
ultra 10 boot warning---corrupt label
Post 302217965 by itik on Thursday 24th of July 2008 02:07:10 AM
07-24-2008
|
|
10 More Discussions You Might Find Interesting
1. Linux
Hi everyone,
OK, I've made a monumental fsck-up of my linux installation AND I did not backup my data properly (idiot!), so I'm really up the proverbial without a paddle here.
Basically the problem is I re-sized my /home partition (hda13) using Partition Magic 8.0, after doing so my mandrake... (0 Replies)
Discussion started by: alarmcall
0 Replies
2. Solaris
I just was given an Ultra 60 that I'm trying to get started so that I can re-load the system with Solaris 10. I can't seem to get the system to boot past the initial memory check. I've tried to do an Stop-A to get to the eeprom, but can't do that. My next step is to try to send a break from the... (0 Replies)
Discussion started by: zosojohnny
0 Replies
3. Solaris
Hi Fellows,
I am trying to mirror 2 identical disks on a SUN Ultra 10 machines (with new installation of Solaris 8). In the process, I found 2 issues:
1. prtvtoc /dev/rdsk/c0t0d0s0 | fmthard -s - /dev/rdsk/c0t1d0s0
Result: Disk partitions between the 2 disks do not match up.
2. manually... (2 Replies)
Discussion started by: o51974
2 Replies
4. Solaris
Hi,
I have a Sun X4200, when I try to reboot the machine it's not detecting the drive and it shows the following error when I try to rebuilt it. I am not sure whether its a bad HD or something else.
Label says 983040 blocks: Drive says 983039 blocks
WARNING:... (1 Reply)
Discussion started by: gunnervarma
1 Replies
5. Solaris
I have created 1 LUN.
1)LUN 00BB 200GB /dev/rdsk/c1t3d44
/dev/rdsk/c2t28d44
/dev/rdsk/c3t19d44
/dev/rdsk/c4t12d44
2) Already added the new entry into sd.conf and rebooted.
3) Already done these:
powercf –q
power config
4) power display dev=all
I can see the new Symmetrix device.... (1 Reply)
Discussion started by: sirius20d
1 Replies
6. UNIX for Advanced & Expert Users
We have an issue here:
The libc.so.6 file (link) is corrupted and it causes the system unbootable. It even doesn't boot to single user mode. How can we boot the system to fix the library file? Or is there any other solutions for this issue?
Here are some boot messages:... (6 Replies)
Discussion started by: aixlover
6 Replies
7. Filesystems, Disks and Memory
I've seen several posts that are similar to what I'm trying to do but no dice. I have a server (SunFire V215) that went belly up. I've set up a new one. I'm getting a corrupt label: wrong magic number error. Everything I'm seeing says label the drives, but if I do I'm afraid I'll lose the data... (0 Replies)
Discussion started by: tnelson
0 Replies
8. Emergency UNIX and Linux Support
Need help/advice urgently.:wall:
I really shot myself in the foot this time. Here is the scenario
Have a Solaris server Solaris 10 x86 Update 8.
Installed an LSI MegaRaid 9280 raid controller and attached a 16 bay JBOD box to it, created a RAID6 virtual drive with 1 hot spare.
Created a... (2 Replies)
Discussion started by: ccj4467
2 Replies
9. Solaris
I am trying to get an old Ultra 45 to boot and it is stuck in a loop. I cannot get anything to come up on a monitor, so when I hook up a serial connection to the TTYa interface I see the following output:
@(#)OBP 4.21.2 2005/12/22 17:17 Sun Ultra 45 Workstation
Clearing TLBs
Loading... (0 Replies)
Discussion started by: Madrox72
0 Replies
10. Solaris
Hi all,
I've just replaced the eprom battery on my Sun Ultra-30 and having boot issues. For some reason its trying to boot off the network instead of the DISK1. Howe can I change it so the open boot does not default to the boot device: NET
Thanks,
Rob (3 Replies)
Discussion started by: robbo007
3 Replies
LEARN ABOUT X11R4
install-solaris
install-solaris(1M) install-solaris(1M) NAME
install-solaris - install the Solaris operating system SYNOPSIS
install-solaris install-solaris invokes the Solaris Install program. Depending on graphical capability and available memory at the time of invocation, install-solaris invokes either a text-based installer or a graphical installer. The following minimum requirements for physical memory dictate which features are available during installation: For SPARC machines: 128 MB Minimum physical memory for all installation types 128 MB Minimum physical memory required for windowing system 384 MB Minimum physical memory required for graphical-based installation For x86 machines: 256 MB Minimum physical memory for all installation types 256 MB Minimum physical memory required for windowing system 512 MB Minimum physical memory required for graphical-based installation In some cases, even if the minimum physical memory is present, available virtual memory after system startup can limit the number of fea- tures available. install-solaris exists only on the Solaris installation media (CD or DVD) and should be invoked only from there. Refer to the for more details. install-solaris allows installation of the operating system onto any standalone system. install-solaris loads the software available on the installation media. Refer to the for disk space requirements. Refer to the for more information on the various menus and selections. See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Availability |SUNWcdrom (Solaris instal- | | |lation media) | +-----------------------------+-----------------------------+ |Interface Stability |Evolving | +-----------------------------+-----------------------------+ pkginfo(1), install(1M), pkgadd(1M), attributes(5) It is advisable to exit install-solaris by means of the exit options in the install-solaris menus. 23 Sep 2005 install-solaris(1M)