07-24-2008
The existing system already uses H/W raid. When I inserted the new disks, I booted from dvd to single user. I used the raidctl command instead to perform the RAID (in the BIOS, after doing Ctrl+C, there was no raid status shown as stated in a SUN manual). I verified using raidctl -l c1t0d0 and it created the RAID 1 successfully and showed the both disks status as GOOD. So I just proceeded to do OS installation.
What we need to do now is, after OS installation etc,etc is completed, we need to swap these 2 disks onto ANOTHER x2100 server (which is using H/W raid now itself too). Will the H/W raid still be intact if I move the disks from systemA to systemB.? Both system are x2100 servers.
9 More Discussions You Might Find Interesting
1. Linux
Hi everyone.
I have a machine which upon to recently only had one hard disk. Now I have another one identical in size and speed and want create a raid set from those two.
The partition layout is that I have three partitions, first one for /boot, the second for / and then a huge LVM partition... (1 Reply)
Discussion started by: Sprellarinn
1 Replies
2. Solaris
Hi all
i would like to ask some suggests about my next job!
I have to install a new Sun Netra T5220, with an additional internal StorageTek SAS HBA Raid.
The problem come in if every disk is now controlled by the HBA, how can I install the OS?
No disk is being detected by the OS.
SAS card... (2 Replies)
Discussion started by: kakabobo
2 Replies
3. UNIX for Dummies Questions & Answers
Hi
Can someone tell me what are the differences between software and hardware raid ?
thx for help. (2 Replies)
Discussion started by: presul
2 Replies
4. Solaris
Dear ALl,
I have a RAID 5 volume which is as below
d120 r 60GB c1t2d0s5 c1t3d0s5 c1t4d0s5 c1t5d0s5
d7 r 99GB c1t2d0s0 c1t3d0s0 c1t4d0s0 c1t5d0s0
d110 r 99GB c1t2d0s4 c1t3d0s4 c1t4d0s4 c1t5d0s4
d8 r 99GB c1t2d0s1 c1t3d0s1... (2 Replies)
Discussion started by: jegaraman
2 Replies
5. Solaris
Hello All,
I have read enough of texts on Raid 01 and Raid 10 on solaris :wall: . But no-where found a way to create them using SVM. Some one pls tell me how to do or Post some link if that helps.
TIA
Curious
solarister (1 Reply)
Discussion started by: Solarister
1 Replies
6. AIX
Hello,
I have a scsi pci x raid controller card on which I had created a disk array of 3 disks
when I type lspv ; I used to see 3 physical disks ( two local disks and one raid 5 disk )
suddenly the raid 5 disk array disappeared ; so the hardware engineer thought the problem was with SCSI... (0 Replies)
Discussion started by: filosophizer
0 Replies
7. Solaris
Server Model: T5120 with 146G x4 disks.
OS: Solaris 10 - installed on c1t0d0.
Plan to use software raid (veritas volume mgr) on c1t2d0 disk.
After format and label the disk, still not able to detect using vxdiskadm.
Question:
Should I remove the hardware raid on c1t2d0 first?
My... (4 Replies)
Discussion started by: KhawHL
4 Replies
8. Red Hat
Im have Oracle Virtualbox and vmware workstation How can i Add2 HDD in Vmware or Virtualbox and Install centos Using Raid Configuration Please give me Tutorial step by Step .. Thanks in Advance
In Virtualbox there is SAS Hard disk So shall i Use it ? (3 Replies)
Discussion started by: babinlonston
3 Replies
9. Red Hat
Hello,
I want to delete a RAID configuration an old server has.
Since i haven't the chance to work with the specific raid controller in the past can you please help me how to perform the configuraiton?
I downloaded IBM ServeRAID Support CD but i wasn't able to configure the video card so i... (0 Replies)
Discussion started by: @dagio
0 Replies
LEARN ABOUT CENTOS
extlinux
extlinux(1) General Commands Manual extlinux(1)
NAME
extlinux - install the SYSLINUX bootloader on a ext2/ext3 filesystem
SYNOPSIS
extlinux [options] directory
DESCRIPTION
EXTLINUX is a new syslinux derivative, which boots from a Linux ext2/ext3 filesystem. It works the same way as SYSLINUX, with a few slight
modifications. It is intended to simplify first-time installation of Linux, and for creation of rescue and other special-purpose boot
disks.
The installer is designed to be run on a mounted directory. For example, if you have an ext2 or ext3 usb key mounted on /mnt, you can run
the following command:
extlinux --install /mnt
OPTIONS
-H, --heads=#
Force the number of heads.
-i, --install
Install over the current bootsector.
-O, --clear-once
Clear the boot-once command.
-o, --once=command
Execute a command once upon boot.
-M, --menu-save=label
Set the label to select as default on the next boot
-r, --raid
Fall back to the next device on boot failure.
--reset-adv
Reset auxiliary data.
-S, --sectors=#
Force the number of sectors per track.
-U, --update
Updates a previous EXTLINUX installation.
-z, --zip
Force zipdrive geometry (-H 64 -S 32).
FILES
The extlinux configuration file needs to be named extlinux.conf and needs to be stored in the extlinux installation directory. For more
information about the contents of extlinux.conf, see syslinux(1) manpage, section files.
BUGS
I would appreciate hearing of any problems you have with SYSLINUX. I would also like to hear from you if you have successfully used SYS-
LINUX, especially if you are using it for a distribution.
If you are reporting problems, please include all possible information about your system and your BIOS; the vast majority of all problems
reported turn out to be BIOS or hardware bugs, and I need as much information as possible in order to diagnose the problems.
There is a mailing list for discussion among SYSLINUX users and for announcements of new and test versions. To join, send a message to
majordomo@linux.kernel.org with the line:
SEE ALSO
syslinux(1)
SYSLINUX for ext2/ext3 filesystem 18 December 2007 extlinux(1)