07-16-2008
As mentioned in the earlier post `route add` command will have an immediate effect i.e without rebooting.
Then I mentioned to edit the file to make it permanent so that it is available even after reboot.
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
The infomation: Sun Ultra10 (SPARC),OS Solaris 8
I finished installed Solaris8 on my workstation, i want configure the net. When i run ,'ifconfig -a ' ,i did't find my familiar 'hme0,hme1' network interface,my interface is good and the reticle is connected correctly.
Pls help me, tell me how... (2 Replies)
Discussion started by: q30
2 Replies
2. Solaris
Withouth being physically at the server, is there a way to tell if the network cable is unplugged? (6 Replies)
Discussion started by: csaunders
6 Replies
3. Solaris
I have a machine that has developed a strange network problem. Anytime it sends an FTP file somewherwe, no problem. When it is the target machine, extremely slow. I checked the /var/adm/messages file and found a few of these:
SUNW,hme0 : No response from Ethernet network : Link down -- cable... (2 Replies)
Discussion started by: hshapiro
2 Replies
4. Solaris
I have a solaris x86 box that ive been having trouble getting on my network, anyone know a good guide that can take me through it step by step? (1 Reply)
Discussion started by: xtremepancakez
1 Replies
5. Solaris
Hi gurus,
I need book to learn about network in Solaris 9
Thanks (2 Replies)
Discussion started by: mass1123
2 Replies
6. Solaris
I have installed solaris x86 on a standalone PC. Now I have connected a LAN cable to it. What do I do next for further configuration or to access internet from that solaris machine? (16 Replies)
Discussion started by: panchpan
16 Replies
7. Solaris
Hi,
i have installed solaris on virtual box in my desktop, i wanted to know how to make it network enabled(nated network). Nated network means it will use same IP as of my windows right? so is it possible that using the same IP i can enable the network on this virtual box.
Thanks in advance. (3 Replies)
Discussion started by: amult
3 Replies
8. Solaris
Hi,
I'm very new to Solaris world and istarted my learnign with a Blade T6320 Server.
I was trying to install Solaris 10.8 from a DVD image over the network.
But from the client(the machine which i want to install Solaris) when i tried boot net , i am getting a message like " cannto find... (5 Replies)
Discussion started by: jerinvjose
5 Replies
9. Solaris
Hi all,
I got a Fujitsu P650 server running on Solaris 9 and we are going to re-install Solaris 10 . W have a build server in a different IP segment. So we setup a boot server and /etc/ethers and /etc/bootparams are all updated. When I issue
boot net -install,
I'm getting the following... (3 Replies)
Discussion started by: mohzub
3 Replies
10. Solaris
Dear All,
I have a solaris Server in which I have 4 network interfaces , out of which only one is used . So all the applications are using this interface .
The interface speed is 1000Mbps . I find no hardware issue or packets g being dropped.
But i find that no of Input and Output... (4 Replies)
Discussion started by: jegaraman
4 Replies
reboot(3C) reboot(3C)
NAME
reboot - reboot system or halt processor
SYNOPSIS
#include <sys/reboot.h>
int reboot(int howto, char *bootargs);
The reboot() function reboots the system. The howto argument specifies the behavior of the system while rebooting and is a mask con-
structed by a bitwise-inclusive-OR of flags from the following list:
RB_AUTOBOOT The machine is rebooted from the root filesystem on the default boot device. This is the default behavior. See boot(1M) and
kernel(1M).
RB_HALT The processor is simply halted; no reboot takes place. This option should be used with caution.
RB_ASKNAME Interpreted by the bootstrap program and kernel, causing the user to be asked for pathnames during the bootstrap.
RB_DUMP The system is forced to panic immediately without any further processing and a crash dump is written to the dump device
(see dumpadm(1M)) before rebooting.
Any other howto argument causes the kernel file to boot.
The interpretation of the bootargs argument is platform-dependent.
Upon successful completion, reboot() never returns. Otherwise, -1 is returned and errno is set to indicate the error.
The reboot() function will fail if:
EPERM The {PRIV_SYS_CONFIG} privilege is not asserted in the effective set of the calling process.
intro(1M), boot(1M), dumpadm(1M), halt(1M), init(1M), kernel(1M), reboot(1M), uadmin(2)
22 Mar 2004 reboot(3C)