07-16-2008
use route add command for the default gateway.
Login as root and fire:
#route add default 192.168.2.167
The ouput will be:
#add net default: gateway 192.168.2.167
Then do netstat -rn as usual and also try to ping thru the gateway out to some host.
Make the changes permanent so that they are available after booting too.
#vi /etc/defaultrouter
AND append IP address: 192.168.2.167
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
The infomation: Sun Ultra10 (SPARC),OS Solaris 8
I finished installed Solaris8 on my workstation, i want configure the net. When i run ,'ifconfig -a ' ,i did't find my familiar 'hme0,hme1' network interface,my interface is good and the reticle is connected correctly.
Pls help me, tell me how... (2 Replies)
Discussion started by: q30
2 Replies
2. Solaris
Withouth being physically at the server, is there a way to tell if the network cable is unplugged? (6 Replies)
Discussion started by: csaunders
6 Replies
3. Solaris
I have a machine that has developed a strange network problem. Anytime it sends an FTP file somewherwe, no problem. When it is the target machine, extremely slow. I checked the /var/adm/messages file and found a few of these:
SUNW,hme0 : No response from Ethernet network : Link down -- cable... (2 Replies)
Discussion started by: hshapiro
2 Replies
4. Solaris
I have a solaris x86 box that ive been having trouble getting on my network, anyone know a good guide that can take me through it step by step? (1 Reply)
Discussion started by: xtremepancakez
1 Replies
5. Solaris
Hi gurus,
I need book to learn about network in Solaris 9
Thanks (2 Replies)
Discussion started by: mass1123
2 Replies
6. Solaris
I have installed solaris x86 on a standalone PC. Now I have connected a LAN cable to it. What do I do next for further configuration or to access internet from that solaris machine? (16 Replies)
Discussion started by: panchpan
16 Replies
7. Solaris
Hi,
i have installed solaris on virtual box in my desktop, i wanted to know how to make it network enabled(nated network). Nated network means it will use same IP as of my windows right? so is it possible that using the same IP i can enable the network on this virtual box.
Thanks in advance. (3 Replies)
Discussion started by: amult
3 Replies
8. Solaris
Hi,
I'm very new to Solaris world and istarted my learnign with a Blade T6320 Server.
I was trying to install Solaris 10.8 from a DVD image over the network.
But from the client(the machine which i want to install Solaris) when i tried boot net , i am getting a message like " cannto find... (5 Replies)
Discussion started by: jerinvjose
5 Replies
9. Solaris
Hi all,
I got a Fujitsu P650 server running on Solaris 9 and we are going to re-install Solaris 10 . W have a build server in a different IP segment. So we setup a boot server and /etc/ethers and /etc/bootparams are all updated. When I issue
boot net -install,
I'm getting the following... (3 Replies)
Discussion started by: mohzub
3 Replies
10. Solaris
Dear All,
I have a solaris Server in which I have 4 network interfaces , out of which only one is used . So all the applications are using this interface .
The interface speed is 1000Mbps . I find no hardware issue or packets g being dropped.
But i find that no of Input and Output... (4 Replies)
Discussion started by: jegaraman
4 Replies
LEARN ABOUT DEBIAN
vde_l3
VDE_L3(1) General Commands Manual VDE_L3(1)
NAME
vde_l3 - Virtual Distributed Ethernet 'Layer 3' Switch.
SYNOPSIS
vde_l3 -v vde_plug:ipaddress/netmask [-v...] [-r target_network/netmask:gateway] [-G default_gw] [-M mgmt_socket]
DESCRIPTION
A vde_l3 connects to one or more vde_switches, performing ip forwarding among its virtual interfaces. A new interface is created at startup
for each -v option given at command line. Static routes to target networks can be defined using the -r option.
vde_l3 -v /var/run/s1.ctl:192.168.0.1/24
connects to the vde sock at /var/run/s1.ctl with its virtual interface ve0, having the address 192.168.0.1 and netmask 255.255.255.0.
vde_l3
-v /var/run/s1.ctl:192.168.0.1/24
-v /var/run/s2.ctl:10.0.0.254/255.255.0.0
connects to the two vde socks, with its virtual interfaces ve0 and ve1, having addressess 192.168.1.0 and 10.0.0.254 respectively. Hosts in
each network can specify the vde_l3 as their gateway to reach the other one.
OPTIONS
-v vde_plug:ipaddress/netmask
Creates a virtual network interfaces on the vde_l3 box, with address ipaddress and netmask netmask. Please note that the netmask can
be specified either in the 'classic' A.B.C.D mode, or just by giving the number of leading bits (f.e., /17 for 255.255.128.0). One
can define as many interfaces as she wants.
-r target_network/netmask:gateway
Specify a static route through gateway to reach hosts in target_network with netmask netmask. One can define as many routes as she
wants.
-G default_gw
Specify a default gateway, to be used whenever no static route is defined for a target host.
-M mgmt_socket
the unix socket where the parameters (interfaces addresses, routes, etc.) can be checked and changed runtime. unixterm(1) can be
used as a remote terminal for wirefilter.
NOTICE
Virtual Distributed Ethernet is not related in any way with www.vde.com ("Verband der Elektrotechnik, Elektronik und Informationstechnik"
i.e. the German "Association for Electrical, Electronic & Information Technologies").
SEE ALSO
vde_switch(1), vdeq(1), unixterm(1), vde_cryptcab(1), wirefilter(1).
AUTHORS
VDE_L3 is a tool by Daniele Lacamera <root@danielinux.net>
VDE is a project by Renzo Davoli <renzo@cs.unibo.it>
Virtual Distributed Ethernet May 7, 2007 VDE_L3(1)