07-15-2008
solaris 8 network 2
hi all,
how do i make sure that the new routing should take effect on the os memory? what should i run after i add all the new "route add ....".
I have an example below:
bash-2.03# netstat -rn
Routing Table: IPv4
Destination Gateway Flags Ref Use Interface
-------------------- -------------------- ----- ----- ------ ---------
192.168.2.0 192.168.2.50 U 1 7 hme0
224.0.0.0 192.168.2.50 U 1 0 hme0
127.0.0.1 127.0.0.1 UH 1 12 lo0
I need to add a default route with 192.168.2.167 and it should take effect on the os right away w/o reboot. How do I do that?
Thanks in advance.
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
The infomation: Sun Ultra10 (SPARC),OS Solaris 8
I finished installed Solaris8 on my workstation, i want configure the net. When i run ,'ifconfig -a ' ,i did't find my familiar 'hme0,hme1' network interface,my interface is good and the reticle is connected correctly.
Pls help me, tell me how... (2 Replies)
Discussion started by: q30
2 Replies
2. Solaris
Withouth being physically at the server, is there a way to tell if the network cable is unplugged? (6 Replies)
Discussion started by: csaunders
6 Replies
3. Solaris
I have a machine that has developed a strange network problem. Anytime it sends an FTP file somewherwe, no problem. When it is the target machine, extremely slow. I checked the /var/adm/messages file and found a few of these:
SUNW,hme0 : No response from Ethernet network : Link down -- cable... (2 Replies)
Discussion started by: hshapiro
2 Replies
4. Solaris
I have a solaris x86 box that ive been having trouble getting on my network, anyone know a good guide that can take me through it step by step? (1 Reply)
Discussion started by: xtremepancakez
1 Replies
5. Solaris
Hi gurus,
I need book to learn about network in Solaris 9
Thanks (2 Replies)
Discussion started by: mass1123
2 Replies
6. Solaris
I have installed solaris x86 on a standalone PC. Now I have connected a LAN cable to it. What do I do next for further configuration or to access internet from that solaris machine? (16 Replies)
Discussion started by: panchpan
16 Replies
7. Solaris
Hi,
i have installed solaris on virtual box in my desktop, i wanted to know how to make it network enabled(nated network). Nated network means it will use same IP as of my windows right? so is it possible that using the same IP i can enable the network on this virtual box.
Thanks in advance. (3 Replies)
Discussion started by: amult
3 Replies
8. Solaris
Hi,
I'm very new to Solaris world and istarted my learnign with a Blade T6320 Server.
I was trying to install Solaris 10.8 from a DVD image over the network.
But from the client(the machine which i want to install Solaris) when i tried boot net , i am getting a message like " cannto find... (5 Replies)
Discussion started by: jerinvjose
5 Replies
9. Solaris
Hi all,
I got a Fujitsu P650 server running on Solaris 9 and we are going to re-install Solaris 10 . W have a build server in a different IP segment. So we setup a boot server and /etc/ethers and /etc/bootparams are all updated. When I issue
boot net -install,
I'm getting the following... (3 Replies)
Discussion started by: mohzub
3 Replies
10. Solaris
Dear All,
I have a solaris Server in which I have 4 network interfaces , out of which only one is used . So all the applications are using this interface .
The interface speed is 1000Mbps . I find no hardware issue or packets g being dropped.
But i find that no of Input and Output... (4 Replies)
Discussion started by: jegaraman
4 Replies
LEARN ABOUT OPENSOLARIS
tc-route
Route classifier in tc(8) Linux Route classifier in tc(8)
NAME
route - route traffic control filter
SYNOPSIS
tc filter ... route [ from REALM | fromif TAG ] [ to REALM ] [ classid CLASSID ] [ action ACTION_SPEC ]
DESCRIPTION
Match packets based on routing table entries. This filter centers around the possibility to assign a realm to routing table entries. For
any packet to be classified by this filter, a routing table lookup is performed and the returned realm is used to decide on whether the
packet is a match or not.
OPTIONS
action ACTION_SPEC
Apply an action from the generic actions framework on matching packets.
classid CLASSID
Push matching packets into the class identified by CLASSID.
from REALM
fromif TAG
Perform source route lookups. TAG is the name of an interface which must be present on the system at the time of tc invocation.
to REALM
Match if normal (i.e., destination) routing returns the given REALM.
EXAMPLES
Consider the subnet 192.168.2.0/24 being attached to eth0:
ip route add 192.168.2.0/24 dev eth0 realm 2
The following route filter will then match packets from that subnet:
tc filter add ... route from 2 classid 1:2
and pass packets on to class 1:2.
NOTES
Due to implementation details, realm values must be in a range from 0 to 255, inclusive. Alternatively, a verbose name defined in
/etc/iproute2/rt_realms may be given instead.
SEE ALSO
tc(8), ip-route(8)
iproute2 21 Oct 2015 Route classifier in tc(8)