07-14-2008
same problem i found in my side. my os is sco 5.0.6
1) you start your new hdd scsi with new installed sco 5.0.6
2) find divvy command and just run it and write the tabel information
3) add your old hdd (currupt hdd) in scsi .
4) again boot with 2 hdd.
5) check again divvy command. it will show you extra table information
*** be carefull in secound you can lost your data **
do not change olddata information just give name for new mount area
eg./mnt
and save it,reboot
now if what you say your hdd is currect then you may found in /mnt
best of luck
pankaj
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
HI ALL,
I need to backup HDD with SCO UNIX. I need to have a full functionaly backup of this hard disk. Does anybody have any tool or subsription how to do it. I tried some SW, but after when I tried to use this copy of my original disk "can not find a root directory". Thanks in advance. (1 Reply)
Discussion started by: jardas
1 Replies
2. SCO
Hi guys,
I have this quick question , is it posible to isntall SCO 5.0.7 on a serial ATA and if it is can you tell me how or maybe a website that has some info about this.
I'm not using any raid, just one HDD.
Thanks a lot (0 Replies)
Discussion started by: josramon
0 Replies
3. UNIX for Advanced & Expert Users
Hello,
I have a P4, 2.4GHz, 256MB ASROCK mainboard: I am trying to install sco 5.0.5 on an 80gb hdd IDE .
I have tried the following techniques:
1. using the updated wd btld image- no success
2. defbootstr biosgeom
3. use interactive divvy, make adjustments using dkinit/dparam during... (0 Replies)
Discussion started by: pude
0 Replies
4. Solaris
Hi Friends,
I am using VMware 6.0 and i want to transfer some files from External HDD so how to mount the Disk, and i am not able to assign any ip to my network card any one can help me how to set ip in VMware.
Thanks and Regards,
Venky.:b: (0 Replies)
Discussion started by: 1409.venkatesh
0 Replies
5. Windows & DOS: Issues & Discussions
Hi,
Unix based,
My harddrive won't boot and I'm looking for a reliable tool
that can mount a hdd on Windows XP and show me the files
stored on a NFS system.
I tried the tool: Ext2IFS but this didn't work.
I found a lot of tools on google to mount nfs share thru a network
but that's... (1 Reply)
Discussion started by: severt
1 Replies
6. Filesystems, Disks and Memory
I started on another thread and full story can be seen here: https://www.unix.com/security/91428-how-reset-root-password-old-unix-system-v.html
But my situation turned to land on this thread now.
I have old scsi HDD out of the UHC UNIX System V Rel. 4.0 Version 3.6 box. And need to read... (1 Reply)
Discussion started by: 82026
1 Replies
7. SCO
Hi all
I have read about mounting crashed HDD from a sco system in this forum. However this I received an image on raw format of the crashed system that was using an IDE HDD. Which method should I mount my image? IDE scsi or USB? The image is stores in an external connected through USB .
Also... (4 Replies)
Discussion started by: OrangeKenny
4 Replies
8. Solaris
I just installed Solaris 11.2 - and it is a bugger. How do I mount an extra HDD that is now formated to NTFS through gparted
it keeps telling me I don't have any ntfs on this laptop. it has two hdds, /dev/sda1 /dev/sdb1 (Linux lingo) Solaris is installed on primary hard drive back of it. then... (2 Replies)
Discussion started by: userx-bw
2 Replies
9. Fedora
once again, mounting another volume or hdd the fstab-file is giving me a headache. May someone could give me a hint how to configure the fstab-file properly to use the hdd.
The following
ls -l /dev/disk/by-uuidis giving me this
Thats the UUID for /dev/sdb1 with the name "save"... (6 Replies)
Discussion started by: 1in10
6 Replies
10. Emergency UNIX and Linux Support
rying it this way, because I can't handle the slices for the second hdd. If there is someone on this forum who can help me out of that misery, he would really save my digital life in this digital ocean.
So not giving up, reading several times the manual of gpart. But the best hint in all that... (0 Replies)
Discussion started by: 1in10
0 Replies
LEARN ABOUT DEBIAN
mhddfs
mhddfs(1) General Commands Manual mhddfs(1)
NAME
mhddfs - The driver combines a several mount points into the single one.
SYNOPSIS
mhddfs /dir1,/dir2[,/path/to/dir3] /path/to/mount [-o options]
mhddfs /dir1 dir2,dir3 /mount/point [-o options]
...
fusermount -u /path/to/mount
fstab record example:
mhddfs#/path/to/dir1,/path/to/dir2 /mnt/point fuse defaults 0 0
mhddfs#/dir1,/dir2,/dir3 /mnt fuse logfile=/var/log/mhddfs.log 0 0
OPTIONS
with an -o option1,option2... you can specify some additional options:
logfile=/path/to/file.log
specify a file that will contain debug information.
loglevel=x
0 - debug messages
1 - info messages
2 - standard (default) messages
mlimit=size[m|k|g]
a free space size threshold If a drive has the free space less than the threshold specifed then another drive will be choosen while creat-
ing a new file. If all the drives have free space less than the threshold specified then a drive containing most free space will be
choosen.
Default value is 4G, minimum value is 100M.
This option accepts suffixes:
[mM] - megabytes
[gG] - gigabytes
[kK] - kilobytes
For an information about the additional options see output of:
mhddfs -h
DESCRIPTION
The file system allows to unite a several mount points (or directories) to the single one. So a one big filesystem is simulated and this
makes it possible to combine a several hard drives or network file systems. This system is like unionfs but it can choose a drive with the
most of free space, and move the data between drives transparently for the applications.
While writing files they are written to a 1st hdd until the hdd has the free space (see mlimit option), then they are written on a 2nd hdd,
then to 3rd etc.
df will show a total statistics of all filesystems like there is a big one hdd.
If an overflow arises while writing to the hdd1 then a file content already written will be transferred to a hdd containing enough of free
space for a file. The transferring is processed on-the-fly, fully transparent for the application that is writing. So this behaviour simu-
lates a big file system.
WARNINGS
The filesystems are combined must provide a possibility to get their parameters correctly (e.g. size of free space). Otherwise the writing
failure can occur (but data consistency will be ok anyway). For example it is a bad idea to combine a several sshfs systems together.
Please read FUSE documentation for a further conception.
COPYRIGHT
Distributed under GPLv3
Copyright (C) 2008 Dmitry E. Oboukhov <dimka@avanto.org>
February 2008 mhddfs(1)