Sponsored Content
Operating Systems SCO Sco 5.06 How To Mount A 2nd Hdd Help Help!!!! Post 302214411 by pankajbraval on Monday 14th of July 2008 02:07:00 AM
Old 07-14-2008
same problem i found in my side. my os is sco 5.0.6
1) you start your new hdd scsi with new installed sco 5.0.6
2) find divvy command and just run it and write the tabel information
3) add your old hdd (currupt hdd) in scsi .
4) again boot with 2 hdd.
5) check again divvy command. it will show you extra table information
*** be carefull in secound you can lost your data **
do not change olddata information just give name for new mount area
eg./mnt
and save it,reboot
now if what you say your hdd is currect then you may found in /mnt

best of luck
pankaj
 

10 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

SCO UNIX HDD full backup

HI ALL, I need to backup HDD with SCO UNIX. I need to have a full functionaly backup of this hard disk. Does anybody have any tool or subsription how to do it. I tried some SW, but after when I tried to use this copy of my original disk "can not find a root directory". Thanks in advance. (1 Reply)
Discussion started by: jardas
1 Replies

2. SCO

SCO 5.0.7 and Serial ATA HDD question

Hi guys, I have this quick question , is it posible to isntall SCO 5.0.7 on a serial ATA and if it is can you tell me how or maybe a website that has some info about this. I'm not using any raid, just one HDD. Thanks a lot (0 Replies)
Discussion started by: josramon
0 Replies

3. UNIX for Advanced & Expert Users

SCO 5.0.5 installation on 80GB HDD

Hello, I have a P4, 2.4GHz, 256MB ASROCK mainboard: I am trying to install sco 5.0.5 on an 80gb hdd IDE . I have tried the following techniques: 1. using the updated wd btld image- no success 2. defbootstr biosgeom 3. use interactive divvy, make adjustments using dkinit/dparam during... (0 Replies)
Discussion started by: pude
0 Replies

4. Solaris

How to mount External HDD in VMware 6.0

Hi Friends, I am using VMware 6.0 and i want to transfer some files from External HDD so how to mount the Disk, and i am not able to assign any ip to my network card any one can help me how to set ip in VMware. Thanks and Regards, Venky.:b: (0 Replies)
Discussion started by: 1409.venkatesh
0 Replies

5. Windows & DOS: Issues & Discussions

NFS HDD mount on Windows XP

Hi, Unix based, My harddrive won't boot and I'm looking for a reliable tool that can mount a hdd on Windows XP and show me the files stored on a NFS system. I tried the tool: Ext2IFS but this didn't work. I found a lot of tools on google to mount nfs share thru a network but that's... (1 Reply)
Discussion started by: severt
1 Replies

6. Filesystems, Disks and Memory

How to mount and read vintage scsi HDD

I started on another thread and full story can be seen here: https://www.unix.com/security/91428-how-reset-root-password-old-unix-system-v.html But my situation turned to land on this thread now. I have old scsi HDD out of the UHC UNIX System V Rel. 4.0 Version 3.6 box. And need to read... (1 Reply)
Discussion started by: 82026
1 Replies

7. SCO

Dd (raw) image of SCO 5.0.6 mount as second hdd

Hi all I have read about mounting crashed HDD from a sco system in this forum. However this I received an image on raw format of the crashed system that was using an IDE HDD. Which method should I mount my image? IDE scsi or USB? The image is stores in an external connected through USB . Also... (4 Replies)
Discussion started by: OrangeKenny
4 Replies

8. Solaris

How to mount ntfs for storage HDD new to Solaris 11.2?

I just installed Solaris 11.2 - and it is a bugger. How do I mount an extra HDD that is now formated to NTFS through gparted it keeps telling me I don't have any ntfs on this laptop. it has two hdds, /dev/sda1 /dev/sdb1 (Linux lingo) Solaris is installed on primary hard drive back of it. then... (2 Replies)
Discussion started by: userx-bw
2 Replies

9. Fedora

Fstab for 2nd hdd, how to?

once again, mounting another volume or hdd the fstab-file is giving me a headache. May someone could give me a hint how to configure the fstab-file properly to use the hdd. The following ls -l /dev/disk/by-uuidis giving me this Thats the UUID for /dev/sdb1 with the name "save"... (6 Replies)
Discussion started by: 1in10
6 Replies

10. Emergency UNIX and Linux Support

2nd hdd is Linux_lvm can't mount MBR on BSD with GPT

rying it this way, because I can't handle the slices for the second hdd. If there is someone on this forum who can help me out of that misery, he would really save my digital life in this digital ocean. So not giving up, reading several times the manual of gpart. But the best hint in all that... (0 Replies)
Discussion started by: 1in10
0 Replies
SMARTCTL(8)						      System Manager's Manual						       SMARTCTL(8)

NAME
smartctl - S.M.A.R.T. control utility SYNOPSIS
smartctl [-cdeglostv] [device] DESCRIPTION
smartctl controls the Self-Monitoring, Analysis and Reporting Technology System(S.M.A.R.T.) built into ATA-3 and later IDE and SCSI-3 Hard Drives. This is used to check the reliability of the hard drive and predict drive failures. TapeAlerts support for SCSI tape drives and changers smartctl is command line utility designed to perform simple S.M.A.R.T. tasks. OPTIONS
smartctl accepts two agruments, options and device in respective order. The options begin with a '-' and multiple options should be begun with a single '-'. The second argument is the device to be controled. ATA device use the form "/dev/hd*" and SCSI devices use the form "/dev/sd*". SCSI devices use only options a,i,c,e,d. For SCSI Tape Drives and Changers with TapeAlerts support use the form "/dev/st*" and "/dev/sg*". TapeAlerts devices use only a,i,c,e,d. i Check if the device supports S.M.A.R.T c Check if device has any S.M.A.R.T. Warranty Failures g Prints only the generic S.M.A.R.T. attributes v Prints only the vendor specific S.M.A.R.T. attributes t Prints only the vendor specific S.M.A.R.T. thresholds l Prints only the S.M.A.R.T. error log a Prints all parameters for c,i,g,v,t,l (for SCSI c,i) e Enables S.M.A.R.T. on device d Disables S.M.A.R.T. on device t Enables S.M.A.R.T. automatic offline self test timer which scans the drive every four hours for disk defects. T Disables S.M.A.R.T. automatic offline self test timer O Runs S.M.A.R.T. Immediate off-line Test S Runs S.M.A.R.T. Short Self Test ( usually under ten minutes) s Runs S.M.A.R.T. Short Self Test in Captive Mode. ( WARNING: This test will busy out drive for length of test. Only run this on drives without any mounted partitions.) X Runs S.M.A.R.T. Extended Self Test ( tens of minutes) x Runs S.M.A.R.T. Extended Self Test in Captive Mode. ( WARNING: This test will busy out drive for length of test. Only run this on drives without any mounted partitions.) A Aborts Non-Captive S.M.A.R.T. Tests. EXAMPLES
smartctl -a /dev/hda - prints all S.M.A.R.T. infomration for drive /dev/hda (Primary Master) smartctl -d /dev/hdd - disable S.M.A.R.T. on drive /dev/hdd (Secondary Slave) AUTHOR
Michael Cornwell, cornwell@acm.org Concurrent Systems Laboratory Jack Baskin School of Engineering University of California Santa Cruz http://csl.cse.ucsc.edu/ smartctl-2.1 September 13, 2001 SMARTCTL(8)
All times are GMT -4. The time now is 05:34 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy