Sponsored Content
Operating Systems Solaris Getting interface names using code Post 302214050 by reborg on Friday 11th of July 2008 07:15:56 PM
Old 07-11-2008
I thought as much, but my nevada machine is broken at the moment.
 

9 More Discussions You Might Find Interesting

1. Programming

How to modify this c code to get full GUI interface for Unix Linux ?

Hi, the following code comes from Unix Linux dialog utility project. Unfortunately, this project is no more actively maintained. Unix Linux dialog utility is made of widget boxes. One of them is mixedgauge.c In the following example I would like to get rid of flickering when run in... (0 Replies)
Discussion started by: jack2
0 Replies

2. Shell Programming and Scripting

Shell Script to display function names (called & defined) in a C++ Source Code

Hello to all, I am looking for a way to display only the names of function (calls & definition) of a C++ source code.There is already a post related to this, but the script is to find the functions using a specific variable, and the replies are not that convincing since they cannot be used for... (2 Replies)
Discussion started by: frozensmilz
2 Replies

3. Shell Programming and Scripting

Searching for file names in a directory while ignoring certain file names

Sun Solaris Unix Question Haven't been able to find any solution for this situation. Let's just say the file names listed below exist in a directory. I want the find command to find all files in this directory but at the same time I want to eliminate certain file names or files with certain... (2 Replies)
Discussion started by: 2reperry
2 Replies

4. Solaris

Command line Interface or GUI Interface not shown on solaris

Dear all, I am a newbie in solaris and I need your advice. I have a Solaris version 5.9 installed on Sunfire V240. I am able to ssh the machine from putty remotely. My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Discussion started by: mbouster
2 Replies

5. SCO

Change SCO - GUI or Desktop interface to DOS based interface

Hi all I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface? If you have any ideas, please tell me then. Thank you (2 Replies)
Discussion started by: TinhNhi
2 Replies

6. IP Networking

Need a bridge from an ethernet interface to a serial interface

This is my situation DOS pc serial cable (sl0) Linux Pc eth1 192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router) I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface. ... (3 Replies)
Discussion started by: mghis
3 Replies

7. UNIX for Dummies Questions & Answers

Adding a network interface to a bonded interface

I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies

8. Solaris

Haed code nxge0 nic interface with full duplex & 1000mbps

Hi All I would need to do hard code of nxge0 nic to full duplex & 1000mbps. So that whenever solaris server come up after reboot. it will show full duplex & 1000mbps setting only. Please also let me know how to do it online through command. regards (0 Replies)
Discussion started by: amity
0 Replies

9. Shell Programming and Scripting

Exclude certain file names while selectingData files coming in different names in a file name called

Data files coming in different names in a file name called process.txt. 1. shipments_yyyymmdd.gz 2 Order_yyyymmdd.gz 3. Invoice_yyyymmdd.gz 4. globalorder_yyyymmdd.gz The process needs to discard all the below files and only process two of the 4 file names available ... (1 Reply)
Discussion started by: dsravanam
1 Replies
SYSTEMD-MACHINE-ID-COMMIT.SERVICE(8)			 systemd-machine-id-commit.service		      SYSTEMD-MACHINE-ID-COMMIT.SERVICE(8)

NAME
systemd-machine-id-commit.service - Commit a transient machine ID to disk SYNOPSIS
systemd-machine-id-commit.service DESCRIPTION
systemd-machine-id-commit.service is an early boot service responsible for committing transient /etc/machine-id files to a writable disk file system. See machine-id(5) for more information about machine IDs. This service is started after local-fs.target in case /etc/machine-id is a mount point of its own (usually from a memory file system such as "tmpfs") and /etc is writable. The service will invoke systemd-machine-id-setup --commit, which writes the current transient machine ID to disk and unmount the /etc/machine-id file in a race-free manner to ensure that file is always valid and accessible for other processes. See systemd-machine-id-setup(1) for details. The main use case of this service are systems where /etc/machine-id is read-only and initially not initialized. In this case, the system manager will generate a transient machine ID file on a memory file system, and mount it over /etc/machine-id, during the early boot phase. This service is then invoked in a later boot phase, as soon as /etc has been remounted writable and the ID may thus be committed to disk to make it permanent. SEE ALSO
systemd(1), systemd-machine-id-setup(1), machine-id(5), systemd-firstboot(1) systemd 237 SYSTEMD-MACHINE-ID-COMMIT.SERVICE(8)
All times are GMT -4. The time now is 12:48 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy