I get nothing on Sparc or x86/64, as I would expect. ksp->ks_module concatenated with ksp->ks_instance and compared with ks->ks_name might give you something, but I wouldn't expect ksp->ks_module to ever return "link" as a value it should return the module name eg. bge, hme or whatever the interface type is.
Hi,
the following code comes from Unix Linux dialog utility project.
Unfortunately, this project is no more actively maintained.
Unix Linux dialog utility is made of widget boxes.
One of them is mixedgauge.c
In the following example I would like to get rid of flickering
when run in... (0 Replies)
Hello to all,
I am looking for a way to display only the names of function (calls & definition) of a C++ source code.There is already a post related to this, but the script is to find the functions using a specific variable, and the replies are not that convincing since they cannot be used for... (2 Replies)
Sun Solaris Unix Question
Haven't been able to find any solution for this situation. Let's just say the file names listed below exist in a directory. I want the find command to find all files in this directory but at the same time I want to eliminate certain file names or files with certain... (2 Replies)
Dear all,
I am a newbie in solaris and I need your advice.
I have a Solaris version 5.9 installed on Sunfire V240.
I am able to ssh the machine from putty remotely.
My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Hi all
I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface?
If you have any ideas, please tell me then. Thank you (2 Replies)
This is my situation
DOS pc serial cable (sl0) Linux Pc eth1
192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router)
I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface.
... (3 Replies)
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Hi All
I would need to do hard code of nxge0 nic to full duplex & 1000mbps. So that whenever solaris server come up after reboot. it will show full duplex & 1000mbps setting only.
Please also let me know how to do it online through command.
regards (0 Replies)
Data files coming in different names in a file name called process.txt.
1. shipments_yyyymmdd.gz
2 Order_yyyymmdd.gz
3. Invoice_yyyymmdd.gz
4. globalorder_yyyymmdd.gz
The process needs to discard all the below files and only process two of the 4 file names available
... (1 Reply)
Discussion started by: dsravanam
1 Replies
LEARN ABOUT CENTOS
epair
EPAIR(4) BSD Kernel Interfaces Manual EPAIR(4)NAME
epair -- A pair of virtual back-to-back connected Ethernet interfaces.
SYNOPSIS
To compile this driver into the kernel, place the following line in your kernel configuration file:
device epair
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_epair_load="YES"
DESCRIPTION
The epair is a pair of Ethernet-like software interfaces, which are connected back-to-back with a virtual cross-over cable.
Each epair interface pair is created at runtime using interface cloning. This is most easily done with the ifconfig(8) create command or
using the cloned_interfaces variable in rc.conf(5). While for cloning you only give either epair or epair<n> the epair pair will be named
like epair<n>[ab]. This means the names of the first epair interfaces will be epair0a and epair0b.
Like any other Ethernet interface, an epair needs to have a network address. Each epair will be assigned a locally administered address by
default, that is only guaranteed to be unique within one network stack. To change the default addresses one may use the SIOCSIFADDR ioctl(2)
or ifconfig(8) utility.
The basic intend is to provide connectivity between two virtual network stack instances. When connected to a if_bridge(4) one end of the
interface pair can also be part of another (virtual) LAN. As with any other Ethernet interface one can configure vlan(4) support on top of
it.
SEE ALSO ioctl(2), altq(4), bpf(4), if_bridge(4), vlan(4), loader.conf(5,) rc.conf(5), ifconfig(8)HISTORY
The epair interface first appeared in FreeBSD 8.0.
AUTHORS
The epair interface was written by Bjoern A. Zeeb, CK Software GmbH, under sponsorship from the FreeBSD Foundation.
BSD July 26, 2009 BSD