Getting interface names using code Post: 302213593

9 More Discussions You Might Find Interesting

1. Programming

How to modify this c code to get full GUI interface for Unix Linux ?

Hi, the following code comes from Unix Linux dialog utility project. Unfortunately, this project is no more actively maintained. Unix Linux dialog utility is made of widget boxes. One of them is mixedgauge.c In the following example I would like to get rid of flickering when run in...

2. Shell Programming and Scripting

Shell Script to display function names (called & defined) in a C++ Source Code

Hello to all, I am looking for a way to display only the names of function (calls & definition) of a C++ source code.There is already a post related to this, but the script is to find the functions using a specific variable, and the replies are not that convincing since they cannot be used for...

3. Shell Programming and Scripting

Searching for file names in a directory while ignoring certain file names

Sun Solaris Unix Question Haven't been able to find any solution for this situation. Let's just say the file names listed below exist in a directory. I want the find command to find all files in this directory but at the same time I want to eliminate certain file names or files with certain...

4. Solaris

Command line Interface or GUI Interface not shown on solaris

Dear all, I am a newbie in solaris and I need your advice. I have a Solaris version 5.9 installed on Sunfire V240. I am able to ssh the machine from putty remotely. My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI...

5. SCO

Change SCO - GUI or Desktop interface to DOS based interface

Hi all I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface? If you have any ideas, please tell me then. Thank you

6. IP Networking

Need a bridge from an ethernet interface to a serial interface

This is my situation DOS pc serial cable (sl0) Linux Pc eth1 192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router) I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface. ...

7. UNIX for Dummies Questions & Answers

Adding a network interface to a bonded interface

I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without...

8. Solaris

Haed code nxge0 nic interface with full duplex & 1000mbps

Hi All I would need to do hard code of nxge0 nic to full duplex & 1000mbps. So that whenever solaris server come up after reboot. it will show full duplex & 1000mbps setting only. Please also let me know how to do it online through command. regards

9. Shell Programming and Scripting

Exclude certain file names while selectingData files coming in different names in a file name called

Data files coming in different names in a file name called process.txt. 1. shipments_yyyymmdd.gz 2 Order_yyyymmdd.gz 3. Invoice_yyyymmdd.gz 4. globalorder_yyyymmdd.gz The process needs to discard all the below files and only process two of the 4 file names available ...

LEARN ABOUT CENTOS

btrfs-debug-tree

BTRFS-DEBUG-TREE(8)					      System Manager's Manual					       BTRFS-DEBUG-TREE(8)

NAME

       btrfs-debug-tree - dump Btrfs filesystem metadata into stdout.

SYNOPSIS

       btrfs-debug-tree [options] <device>

DESCRIPTION

       btrfs-debug-tree  is used to dump the whole tree of the given device.  This is maybe useful for analyzing filesystem state or inconsistence
       and has a positive educational effect on understanding the internal structure.  device is the device file where the filesystem is stored.

       Options

       -e   print detailed extents info.

       -d   print info of btrfs device and root tree dirs only.

       -r   print info of roots only.

       -b <block_num>
	    print info of the specified block only.

EXIT CODE

       btrfs-debug-tree will return 0 if no error happened.  If any problems happened, 1 will be returned.

AUTHOR

       Written by Shilong Wang and Wenruo Qu.

COPYRIGHT

       Copyright (C) 2013 Fujitsu, Inc.  License GPLv2: GNU GPL version 2 <http://gnu.org/licenses/gpl.html>.
       This is free software: you are free  to	change	and  redistribute  it. There is NO WARRANTY, to the extent permitted by law.

SEE ALSO

       mkfs.btrfs(8)

															       BTRFS-DEBUG-TREE(8)