07-08-2008
Can you show me the routing table ?
You can use
netstat -nr
OR
route
9 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
hi, everyone:
alpha 600 au true64 Unix 4.0f
my network cart is set "Auto-Negotiate".After operate system startup,the network will be disconnected by itself at sometime. I found some prompt in /usr/adm/messages.
"tu0 :transmit FIFO underflow:threshold raised to :256 byteŁ¬link up... (1 Reply)
Discussion started by: q30
1 Replies
2. UNIX for Advanced & Expert Users
Hi expert,
Need some help on network interface issue..
I have added 2 x NIC card onto the Ultra 2 system recently and configured as hme1 and hme2. I have unconfigured the onboard hme0 network interface and it was running fine till few days later, i keep recieving error messages showing hme0... (6 Replies)
Discussion started by: sc2005
6 Replies
3. Solaris
Hi guys,
Hope somebody can help me on this. I have a Sun Sparc 20 workstation and it has a boot problem. During boot, an error message " ifconfig:socket: Bad File Number" come up and the workstation hang (cannot boot).
I did boot -s and checked using ifconfig -a command but i got the same... (0 Replies)
Discussion started by: kroegand
0 Replies
4. AIX
Hi every body,
I have a Fiber Channel interface (fcs2) in AIX 5.2. This interface was fine & up but for some reason I could not return this interface UP again after I set it DOWN.
When I tried to set this interface UP I encountered the following error:
Method error... (7 Replies)
Discussion started by: aldowsary
7 Replies
5. Red Hat
Hi
I have installed OEL 4 on my dell XPS laptop. But when i connect the LAN cable and try to acesss internet. it does not work. the led's in the port do not blink when i plug in the cable .do i need some drivers please suggest.
Thanks
Ankur (2 Replies)
Discussion started by: ankurk
2 Replies
6. Programming
Hello, I'm trying to use libcurl multi interface to fetch several data in parallel. I would expect this to be faster than performing repeated fetches using the easy interface, but for some reason I can't obtain any speed up at all: using the multi interface actually turns out to be MUCH slower than... (2 Replies)
Discussion started by: clalfa
2 Replies
7. Solaris
Hi
i have replace a NIC card on solaris 10 when i give the following command
ifconfig -a
it just show the lo0 (only loop back with inet 127.0.0.1)
when i give the following command to config the interface,
ifconfig elxl0 plumb
ifconfig: plumb: elxl0: no such interface
please help... (11 Replies)
Discussion started by: malikshahid85
11 Replies
8. Solaris
HI,
genunix: NOTICE: ce0: xcvr addr:0x01 - link up 100 Mbps half duplex
genunix: WARNING: ce0: fault detected external to device; service degraded
genunix: WARNING: ce0: xcvr addr:0x01 - link down
genunix: NOTICE: ce0: fault cleared external to device; service available
genunix: ... (4 Replies)
Discussion started by: sunnybee
4 Replies
9. Red Hat
Dear All ,
While taking backups in one Linux Server , we find one alert came with regard to Network Interface Card.
Pl find the below alert.
Network Interface Card performance for NIC:eth1 has exceeded Major threshold.
Bytes sent and received per second (Average)= 105540.303101... (6 Replies)
Discussion started by: jegaraman
6 Replies
LEARN ABOUT SUNOS
inet_type
inet_type(4) File Formats inet_type(4)
NAME
inet_type - default Internet protocol type
SYNOPSIS
/etc/default/inet_type
DESCRIPTION
The inet_type file defines the default IP protocol to use. Currently this file is only used by the ifconfig(1M) and netstat(1M) commands.
The inet_type file can contain a number of <variable>=<value> lines. Currently, the only variable defined is DEFAULT_IP, which can be
assigned a value of IP_VERSION4, IP_VERSION6, or BOTH.
The output displayed by the ifconfig and netstat commands can be controlled by the value of DEFAULT_IP set in inet_type file. By default,
both commands display the IPv4 and IPv6 information available on the system. The user can choose to suppress display of IPv6 information by
setting the value of DEFAULT_IP. The following shows the possible values for DEFAULT_IP and the resulting ifconfig and netstat output that
will be displayed:
IP_VERSION4 Displays only IPv4 related information. The output displayed is backward compatible with older versions of the ifconfig(1M)
and netstat(1M) commands.
IP_VERSION6 Displays both IPv4 and IPv6 related information for ifconfig and netstat.
BOTH Displays both IPv4 and IPv6 related information for ifconfig and netstat.
The command-line options to the ifconfig and netstat commands override the effect of DEFAULT_IP as set in the inet_type file. For example,
even if the value of DEFAULT_IP is IP_VERSION4, the command
example% ifconfig -a6
will display all IPv6 interfaces.
EXAMPLES
Example 1: Suppressing IPv6 Related Output
This is what the inet_type file must contain if you want to suppress IPv6 related output:
DEFAULT_IP=IP_VERSION4
SEE ALSO
ifconfig(1M), netstat(1M)
SunOS 5.10 16 Jun 1999 inet_type(4)