|
|
Sponsored Content
Top Forums
UNIX for Dummies Questions & Answers
Multi Network card interface problem
Post 302212641 by hcliff on Tuesday 8th of July 2008 04:29:42 AM
07-08-2008
|
|
9 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
hi, everyone:
alpha 600 au true64 Unix 4.0f
my network cart is set "Auto-Negotiate".After operate system startup,the network will be disconnected by itself at sometime. I found some prompt in /usr/adm/messages.
"tu0 :transmit FIFO underflow:threshold raised to :256 byteŁ¬link up... (1 Reply)
Discussion started by: q30
1 Replies
2. UNIX for Advanced & Expert Users
Hi expert,
Need some help on network interface issue..
I have added 2 x NIC card onto the Ultra 2 system recently and configured as hme1 and hme2. I have unconfigured the onboard hme0 network interface and it was running fine till few days later, i keep recieving error messages showing hme0... (6 Replies)
Discussion started by: sc2005
6 Replies
3. Solaris
Hi guys,
Hope somebody can help me on this. I have a Sun Sparc 20 workstation and it has a boot problem. During boot, an error message " ifconfig:socket: Bad File Number" come up and the workstation hang (cannot boot).
I did boot -s and checked using ifconfig -a command but i got the same... (0 Replies)
Discussion started by: kroegand
0 Replies
4. AIX
Hi every body,
I have a Fiber Channel interface (fcs2) in AIX 5.2. This interface was fine & up but for some reason I could not return this interface UP again after I set it DOWN.
When I tried to set this interface UP I encountered the following error:
Method error... (7 Replies)
Discussion started by: aldowsary
7 Replies
5. Red Hat
Hi
I have installed OEL 4 on my dell XPS laptop. But when i connect the LAN cable and try to acesss internet. it does not work. the led's in the port do not blink when i plug in the cable .do i need some drivers please suggest.
Thanks
Ankur (2 Replies)
Discussion started by: ankurk
2 Replies
6. Programming
Hello, I'm trying to use libcurl multi interface to fetch several data in parallel. I would expect this to be faster than performing repeated fetches using the easy interface, but for some reason I can't obtain any speed up at all: using the multi interface actually turns out to be MUCH slower than... (2 Replies)
Discussion started by: clalfa
2 Replies
7. Solaris
Hi
i have replace a NIC card on solaris 10 when i give the following command
ifconfig -a
it just show the lo0 (only loop back with inet 127.0.0.1)
when i give the following command to config the interface,
ifconfig elxl0 plumb
ifconfig: plumb: elxl0: no such interface
please help... (11 Replies)
Discussion started by: malikshahid85
11 Replies
8. Solaris
HI,
genunix: NOTICE: ce0: xcvr addr:0x01 - link up 100 Mbps half duplex
genunix: WARNING: ce0: fault detected external to device; service degraded
genunix: WARNING: ce0: xcvr addr:0x01 - link down
genunix: NOTICE: ce0: fault cleared external to device; service available
genunix: ... (4 Replies)
Discussion started by: sunnybee
4 Replies
9. Red Hat
Dear All ,
While taking backups in one Linux Server , we find one alert came with regard to Network Interface Card.
Pl find the below alert.
Network Interface Card performance for NIC:eth1 has exceeded Major threshold.
Bytes sent and received per second (Average)= 105540.303101... (6 Replies)
Discussion started by: jegaraman
6 Replies
LEARN ABOUT OPENSOLARIS
i2bsc
bscv(7D) Devices bscv(7D) NAME
bscv, bscbus, i2bsc - Blade support chip interface driver DESCRIPTION
The bscv, bscbus and i2bsc drivers interface with the Blade support chip used on Sun Microsystem's Blade server products. These drivers provide a conduit for passing control, environmental, cpu signature and event information between Solaris and the Blade support chip. These drivers do not export public interfaces. Instead they make information available via picl, prtdiag, prtfru and related tools. In addition, these drivers log Blade support chip environmental event information into system logs. FILES
/platform/sun4u/kernel/drv/sparcv9/bscbus 64-bit ELF kernel driver /platform/sun4u/kernel/drv/sparcv9/bscv 64-bit ELF kernel driver /platform/sun4u/kernel/drv/sparcv9/i2bsc 64-bit ELF kernel driver /platform/i86pc/kernel/drv/bscbus 32-bit ELF kernel file (x86 only) /platform/i86pc/kernel/drv/bscv 32-bit ELF kernel file (x86 only) ATTRIBUTES
See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ |ATTRIBUTE TYPE |ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Architecture |Limited to systems with | | |Blade Support Chip | +-----------------------------+-----------------------------+ |Availability |SUNWcar.u, SUNWcar.i | +-----------------------------+-----------------------------+ SunOS 5.11 22 August 2003 bscv(7D)