07-08-2008
Your system try to mount an external resource (File system)
Maybe the server is not reachable or not right configured.
Test the network connection on both sides (Firewall?)
On our system:
more /etc/vfstab # If your system mount the external file system automatically
On the NFS server:
dfshares # shows what is shared now
more /etc/dfs/dfstab # configuration file
If the two system are both solaris system there is normaly no problem. But if there is a linux server use you have to check the version of nfs
output of /etc/default/nfs
# Sets the maximum version of the NFS protocol that will be registered
# and offered by the server. The default is 4.
#NFS_SERVER_VERSMAX=4
many question but no response (logfiles etc).
It makes no fun do homework for other.
Br Joerg
10 More Discussions You Might Find Interesting
1. SCO
HI,
During the system bootup, following errors are being logged in "syslog"
i) unix1 rpcbind: netdir_getbyname failed on tcp for host unix1, se
rvice rpcbind
ii)unix1 rpcbind: netdir_getbyname failed on udp for host unix1, se
rvice rpcbind
iii)unix1 in.snmpd: unix1: Host unknown.
... (0 Replies)
Discussion started by: tayyabq8
0 Replies
2. UNIX for Dummies Questions & Answers
I'm just going to throw this out there because I have no clue what is causing this problem or how to fix it. selinux is not enabled nor is any sort of firewall. (To my knowledge -- I did a kickstart install with firewall --disabled )
# rpcinfo
program version netid address ... (1 Reply)
Discussion started by: Colton
1 Replies
3. Linux
Hi guys,
i explain my problem:
I've FC10 64bit installed on a server Dell R410.
When i boot the system with eth0 or eth1 linked (only one eth linked), all work fine and the system start normally.
When i boot the system with eth0 + eth1 linked,
the system hang when the rpcind service... (1 Reply)
Discussion started by: andreaden
1 Replies
4. Solaris
while i trying to mount from NAS i have this messages
mount -F nfs -o rw 172.16.110.13:/tremabkup /tremabkup
nfs mount: 172.16.110.13: : RPC: Rpcbind failure - RPC: Timed out
nfs mount: retrying: /tremabkup
nfs mount: 172.16.110.13: : RPC: Rpcbind failure - RPC: Timed out
nfs mount:... (2 Replies)
Discussion started by: thecobra151
2 Replies
5. Solaris
Hello I am having an issue with a server SUN FIRE T2000 (Solaris 10).
First of all the server didn't boot normaly so I did a full restoration of the file systems.
Now the server boot, most of the services are available (not all the services), but I keep on seeing
RPC: Rpcbind failure -... (4 Replies)
Discussion started by: feg
4 Replies
6. Solaris
C: Rpcbind failure - RPC: Timed out error (solaris)
hello an nfs server on my sun fire v440 is not responding , i get the error bellow and lots of my networking services are not reponding, please helppppp its an emergency
RPC: Rpcbind failure - RPC: Timed out
i also get
NFS server... (2 Replies)
Discussion started by: feg
2 Replies
7. UNIX for Dummies Questions & Answers
hi power went out. next day unix sco wont boot up error code 303. any help appreciated as we are clueless. (11 Replies)
Discussion started by: fredthayer
11 Replies
8. Solaris
Fails to mount the server (10.125.224.22) during installation of a software on client, throwing the below error:
nfs mount: 10.125.224.22: : RPC: Rpcbind failure - RPC: Timed out
nfs mount: retrying: /cdrom
This happened after complete shutdown of the lab. The server came up fine but most... (1 Reply)
Discussion started by: frintocf
1 Replies
9. Ubuntu
Hi I am trying to configure NIS client on my Ubuntu 12.04.
But I could not put portmap without uninstalling rpcbind.
Do I need to have rpcbind there on the server, or how can I have both portmap and rpcbind at same time there on the server, because it's having conflict. (1 Reply)
Discussion started by: nixhead
1 Replies
10. Solaris
Hello all,
I have read just about every rpcbind not starting thread and article on the internet it seems, but I have not found a solution to my problem as of yet. I have a solaris 10 server that has been running with no problems for a while. The other day it crashed and would not boot to the gui... (2 Replies)
Discussion started by: Madrox72
2 Replies
LEARN ABOUT MINIX
mount.nfs
MOUNT.NFS(8) System Manager's Manual MOUNT.NFS(8)
NAME
mount.nfs, mount.nfs4 - mount a Network File System
SYNOPSIS
mount.nfs remotetarget dir [-rvVwfnsh ] [-o options]
DESCRIPTION
mount.nfs is a part of nfs(5) utilities package, which provides NFS client functionality.
mount.nfs is meant to be used by the mount(8) command for mounting NFS shares. This subcommand, however, can also be used as a standalone
command with limited functionality.
remotetarget is a server share usually in the form of servername:/path/to/share. dir is the directory on which the file system is to be
mounted.
Under Linux 2.6.32 and later kernel versions, mount.nfs can mount all NFS file system versions. Under earlier Linux kernel versions,
mount.nfs4 must be used for mounting NFSv4 file systems while mount.nfs must be used for NFSv3 and v2.
OPTIONS
-r Mount file system readonly.
-v Be verbose.
-V Print version.
-w Mount file system read-write.
-f Fake mount. Don't actually call the mount system call.
-n Do not update /etc/mtab. By default, an entry is created in /etc/mtab for every mounted file system. Use this option to skip making
an entry.
-s Tolerate sloppy mount options rather than fail.
-h Print help message.
nfsoptions
Refer to nfs(5) or mount(8) manual pages.
NOTE
For further information please refer nfs(5) and mount(8) manual pages.
FILES
/etc/fstab file system table
/etc/mtab table of mounted file systems
SEE ALSO
nfs(5), mount(8),
AUTHOR
Amit Gud <agud@redhat.com>
5 Jun 2006 MOUNT.NFS(8)