07-06-2008
Ethernet card drivers issue...
I need to install ethernet card drivers on intel machine. How can i know which Ethernet card interface (sfe,rh,rtls...) is it? How can i know the speed of that card? How can i know network traffic ? If network traffic is more with that interface what should i do?
Thanks in advance
Last edited by younus_syed; 07-06-2008 at 02:23 PM..
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
I installed Solaris 8 on Compaq EN733 system which has Intel /100 Network Card. When I ran 'ifconfig -a', it did not show any nic card attarched to it. I am not sure is this driver problem or something else.
Any help will be highly appreciated.
Thanks. (4 Replies)
Discussion started by: s_aamir
4 Replies
2. Filesystems, Disks and Memory
Hi,
How can i check the speed of the Ethernet card that my Sun server has and also how can i change it to full Duplex if it is set to half duplex? What is the file that takes care of this? (3 Replies)
Discussion started by: i2admin
3 Replies
3. IP Networking
I have searched this forum for solution and have drawn a blank... so I come to you for help :)
I an a Win XP user that has no problem getting on internet when I am on that OS (currently on it right now ;)). I installed red hat 9 and when I use that OS, I cannot get a connection. I ran the... (10 Replies)
Discussion started by: Minnesota Red
10 Replies
4. UNIX for Dummies Questions & Answers
I am an extreme novice trying to learn Linux. I have redhat 9 installed in a computer I built specifically to install and learn linux. I have an asus a7v8x-x motherboard with the realtek 10/100 mbps ethernet card. I also installed a Jaht adapter jn-1110r32c ethernet card. I cannot get the... (2 Replies)
Discussion started by: Tony Empire
2 Replies
5. SCO
Installed a replacement 3com pci card on an ibm PC 300 GL, running OpenServer 6.0 , brought up system, and recieved this message:
Fsstat:/dev/boot mounted
Mounted /stand filesystem
System auditing is not enabled.
Dlpid:Unable to open network adapter driver (/dev/mdi/r8e0)
Dlpid:No such... (0 Replies)
Discussion started by: tazmss1
0 Replies
6. IP Networking
What command do I use to show mw the ethernet card, I have tried ipconfig -a (1 Reply)
Discussion started by: dhlopomo
1 Replies
7. Solaris
Hi all,
i have configured my solaris 5 .10 for internet connection by editing the files /etc/hosts/,/etc/resolve.config,/etc/defalutrouter and nsswitchconfig .
during installation i was not requested for ip adddress even i plugged network cable.
am i need to install any network card... (2 Replies)
Discussion started by: srikanthg
2 Replies
8. AIX
Hi,
is it possible to find out network utilization of etherenet card in %?
Regards,
Manoj (2 Replies)
Discussion started by: manoj.solaris
2 Replies
9. Linux
Hi,
Actually i want to see Offload parameter for my Eth card.
Then after i try using this command
Anybody can explain ?
Is there any problem with my eth card ? (1 Reply)
Discussion started by: justbow
1 Replies
10. Solaris
Hi Gurus of Solaris.
I have a problem yesterday when I was installing solaris in a x86 equipement
I attached some log that I capture when I try to resolve the problem
Any guru that can help please.
Any command or procedure that I can run, please advice me
Regards
Andres (10 Replies)
Discussion started by: andresguillen
10 Replies
LEARN ABOUT REDHAT
axnet_cs
AXNET_CS(4) Kernel Interfaces Manual AXNET_CS(4)
NAME
axnet_cs - Asix AX88190 chipset PCMCIA Ethernet Driver
SYNOPSIS
insmod axnet_cs.o [pc_debug=n] [irq_list=i,j,...]
DESCRIPTION
Axnet_cs is a driver for PCMCIA ethernet cards based on the Asix AX88190 chipset. These cards are mostly NE2000 compatible but have sev-
eral bugs that are sufficiently tricky to work around that a separate driver was deemed necessary. When this driver is bound to a card, it
allocates the next available ethernet device (eth0..eth#). This device name will be reported in the kernel log file, and passed on to
cardmgr(8).
PARAMETERS
pc_debug=n
Selects the PCMCIA debugging level. This parameter is only available if the module is compiled with debugging enabled. A non-zero
value enables debugging.
irq_list=i,j,...
Specifies the set of interrupts that may be allocated by this driver.
DIAGNOSTICS
axnet_cs: this is not an AX88190 card!
Indicates that this card is probably a normal NE2000 compatible card, which requires the pcnet_cs driver.
eth#: interrupt(s) dropped!
Indicates that the driver did not receive an interrupt notification for some reason. The driver will poll the card (with a signifi-
cant performance penalty) if the problem persists. The most likely cause is an interrupt conflict and/or host bridge configuration
problem.
AUTHOR
David Hinds - dahinds@users.sourceforge.net
SEE ALSO
cardmgr(8), pcmcia(5).
pcmcia-cs 2001/08/17 12:51:58 AXNET_CS(4)