07-01-2008
As I said, please tar without absolute paths. You can get more problems of this than you'd like. Just create some tmp subdirectory close to your destination, uncompress/untar it there and move it to where it belongs.
10 More Discussions You Might Find Interesting
1. Shell Programming and Scripting
hi all,
kindly help me how to extract one file form .tar.gz without uncompressing .tar.gz file.
thanks in advance
bali (2 Replies)
Discussion started by: balireddy_77
2 Replies
2. UNIX for Advanced & Expert Users
In order to save diskspace and avoid of disk full during
unzip then extract the tar file
is there any tar unzip command would unzip and extract tar at the same time
(test123.tar.gz)
thank in advance (6 Replies)
Discussion started by: darkrainbow
6 Replies
3. Shell Programming and Scripting
Hi,
This is my first post here - I'm hoping I can get some help! I have searched these forums and othersand not getting anything that works.
I am trying to extract a single file from a tar archive to a diffierent location than it will default to.
For example my tar log shows me ...
a... (3 Replies)
Discussion started by: littleIdiot
3 Replies
4. UNIX for Advanced & Expert Users
I just want to extract one sigle file from an .ear archieve instead of extracting whole ear.
Can anyone help me on this? (4 Replies)
Discussion started by: harshal_dcx
4 Replies
5. UNIX for Dummies Questions & Answers
Hello
I take a backup using the following command on Solaris 9
tar cvf /dev/rmt/0n data
the data volume contains a number of files say a, b, c , d ... etc
Now I want to restore only one file (eg b) from the data volume.
When I issue the command
tar xvf /dev/rmt/0n data/b... (1 Reply)
Discussion started by: rahmantanko
1 Replies
6. Shell Programming and Scripting
I have a tar file that contains multiple .Z files. Hence I need to issue a tar command followed by a gzip command to fully extract the files. How do I do it in a single command?
What I'm doing now is
tar xvf a.tar (this will output 1.Z and 2.Z)
gzip -d *.Z (to extract 1.Z and 2.Z) (9 Replies)
Discussion started by: ericlim
9 Replies
7. UNIX for Dummies Questions & Answers
I would like to confirm my file.tar is been tar-ed correctly before I remove them. But I have very limited disc space to untar it.
Can I just do the listing instead of actual extract it? Can I say confirm folder integrity if the listing is sucessful without problem?
tar tvf file1.tar
... (1 Reply)
Discussion started by: vivien_chu
1 Replies
8. Shell Programming and Scripting
Hi,
I need to extract a single file from a tar file to another directory.
So far I have this:
This one extract a single file to same directory:
tar -xvf filename.tar ./file.txt
I tried this but its not working
tar -xvf filename.tar /home/dir ./file.txt
or this: (6 Replies)
Discussion started by: erin00
6 Replies
9. UNIX for Dummies Questions & Answers
Hello Team,
Would you please help me with a UNIX command that would check if file is a tar file.
if we dont have that , can you help me with UNIX command that would check if file ends with .tar
Thanks in advance. (10 Replies)
Discussion started by: sanjaydubey2006
10 Replies
10. UNIX for Beginners Questions & Answers
Hi All,
First of all I don't know whether this is possible. or no. Thought of getting experts thought.
I am having a tar file which contains zipped file in it . I tried individual command with extraction and it worked
tar -tvf TRANS_279.tar
-rw-rw-r-- qqa00 1394 2016-10-03 10:39:19... (8 Replies)
Discussion started by: arunkumar_mca
8 Replies
LEARN ABOUT HPUX
sendfiles
SENDFILES(1) [nmh-1.5] SENDFILES(1)
NAME
sendfiles - send multiple files via a MIME message
SYNOPSIS
sendfiles [delay] mailpath subject file1 [file2 ...]
DESCRIPTION
The shell script sendfiles, is used to send a collection of files and directories via electronic mail.
sendfiles mailpath "subject" files ...
sendfiles will archive the files and directories you name with the tar command, and then mail the compressed archive to the "mailpath" with
the given "subject". The archive will be automatically split up into as many messages as necessary in order to get past most mailers.
Sometimes you want sendfiles to pause after posting a partial message. This is usually the case when you are running sendmail and expect
to generate a lot of partial messages. If the first argument given to sendfiles starts with a dash, then it is interpreted as the number
of seconds to pause in between postings, e.g.,
sendfiles -30 mailpath "subject" files ...
will pause 30 seconds in between each posting.
Extracting the Received Files
When these messages are received, invoke mhstore once for the list of messages. The default is for mhstore to store the combined parts as
a new message in the current folder, although this can be changed using storage formatting strings. You can then use mhlist to find out
what's inside; possibly followed by mhstore again to write the archive to a file where you can subsequently uncompress and untar it. For
instance:
% mhlist 5-8
msg part type/subtype size description
5 message/partial 47K part 1 of 4
6 message/partial 47K part 2 of 4
7 message/partial 47K part 3 of 4
8 message/partial 18K part 4 of 4
% mhstore 5-8
reassembling partials 5,6,7,8 to folder inbox as message 9
% mhlist -verbose 9
msg part type/subtype size description
9 application/octet-stream 118K
(extract with uncompress | tar xvpf -)
type=tar
conversions=compress
% mhstore 9
% uncompress < 9.tar.Z | tar xvpf -
Alternately, by using the -auto switch, mhstore will automatically do the extraction for you:
% mhlist 5-8
msg part type/subtype size description
5 message/partial 47K part 1 of 4
6 message/partial 47K part 2 of 4
7 message/partial 47K part 3 of 4
8 message/partial 18K part 4 of 4
% mhstore 5-8
reassembling partials 5,6,7,8 to folder inbox as message 9
% mhlist -verbose 9
msg part type/subtype size description
9 application/octet-stream 118K
(extract with uncompress | tar xvpf -)
type=tar
conversions=compress
% mhstore -auto 9
-- tar listing appears here as files are extracted
As the second tar listing is generated, the files are extracted. A prudent user will never put -auto in the .mh_profile file. The correct
procedure is to first use mhlist to find out what will be extracted. Then mhstore can be invoked with -auto to perform the extraction.
FILES
$HOME/.mh_profile The user profile
PROFILE COMPONENTS
Path: To determine the user's nmh directory
Current-Folder: To find the default current folder
SEE ALSO
mhbuild(1), mhlist(1), mhshow(1), mhstore(1). Proposed Standard for Message Encapsulation (RFC-934)
DEFAULTS
`-noverbose'
CONTEXT
None
MH.6.8 11 June 2012 SENDFILES(1)