06-30-2008
It's hard to give a specific answer when all we have is "I checked this and it looks ok" or "it worked before".
I'd suggest the following, since the process hangs at the remote boot:
1.-Make sure that the jumpstart directory where the boot files are is properly shared.
2.- Remove the client from the jumpstart with rm_install_client
3.- remove everything from the /tftpboot directory
4.- Erase bootparams, ethers, and any host in hosts that doesn't need to be there.
5.- Add the client back, and try the jump again.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I would like to upgrade the memory in my Sun Blade 150 workstation. In reading through Sun's Blade 150 DIMM Installation Guide, it indicates that the memory must be "certified by Sun for the Sun Blade 150 system."
Does anyone know if any SDRAM, PC133 • CL=2 • Unbuffered • ECC • 133MHz • 3.3V ... (2 Replies)
Discussion started by: here2learn
2 Replies
2. UNIX for Dummies Questions & Answers
Hi, I am new to UNIX. I have a Sun Blade 150 worksation. I used a Dell monitor and Dell keyboard as input and output devices. However, workstation always told me that keyboard couldn't be found. I used Dell keyboard with USB and Dell keyboard with series connector. It all didn't work. Please help... (10 Replies)
Discussion started by: duke0001
10 Replies
3. Solaris
I'm not familiar with this particular machine and it's baffling me. For those that are familar with the workstation, allow me to paint a picture. If you were looking down on the machine (open) you would see the main board and then a riser board. On the left side of the riser board are jacks... (1 Reply)
Discussion started by: silversaleen68
1 Replies
4. Solaris
Hi,
I have a Solaris 8.0 BLADE 150 machine. I have an onboard graphics alongwith an addon XVR500 graphics card. Now, when I use the motherboard graphics, I am not able to login to the XWINDOWS terminal, instead it stays on the console.
But, if I insert the monitor cable to the XVR500 port,... (2 Replies)
Discussion started by: angshuman_ag
2 Replies
5. Solaris
I have recently re-installed Solaris 10 on a Sun Blade 150 followed by a patch set (10_Recommended) dated 2011.12.05.
I have just noticed /bin/sun now returns false, rather than true. See below.
$ uname -a
SunOS myblade1 5.10 Generic_147440-07 sun4u sparc SUNW,Sun-Blade-100
$ /bin/sparc &&... (1 Reply)
Discussion started by: apmcd47
1 Replies
6. Solaris
Hi everyone
can someone please explain to me how to install solaris 10 on a sunblade 1500 using cdrom?
Thanks for your assistance (1 Reply)
Discussion started by: cjashu
1 Replies
7. Solaris
Hello,
Ive just aquired a blade 150 off ebay.Im new to suns and are having a problem getting it to boot off the cdrom.Openboot continuously tries to do a network boot and I cant enter any commands.Im using an average pc keyboard and it definetly works.Thanks for any help.:wall: (3 Replies)
Discussion started by: chucky
3 Replies
8. Solaris
Hello,
I cant get my blade box to boot off the harddrive after installing solaris 10.I can get to a root prompt after issuing "boot cdrom -s".I tried booting off disk0 and disk1,but I get "the file just loaded does not seem to be executable".Thanks for any help.:wall: (4 Replies)
Discussion started by: chucky
4 Replies
9. Solaris
Hi everybody,
I'm having big troubles in installing Solaris 8 on a Sun Blade 150.
Here are some system specs:
Sun Blade 150 (UltraSPARC-IIe 550MHz)
RAM: 256MB
OBP 4.10.6 2003/06/06 12:30
POST 2.0.1 2001/08/23 17:13
When I try to boot from Solaris 8 CD with boot cdrom or... (10 Replies)
Discussion started by: Vortigern
10 Replies
10. Solaris
hello
i have a forte gamma camera Philips device . and its a medical device. this medical device is came with sun blade 150 pc and pegasys is printed on the sun blade pc .the problem is when i switched the power on , the sun blade runs and a white screen appear with the information about the... (6 Replies)
Discussion started by: moh_abaloo
6 Replies
LEARN ABOUT NETBSD
isibootd
ISIBOOTD(8) BSD System Manager's Manual ISIBOOTD(8)
NAME
isibootd -- TRFS based network boot server
SYNOPSIS
isibootd [-d tracelevel] [-i interface] [-s directory]
DESCRIPTION
The isibootd command is a server which supports OMRON LUNA's network boot protocol based on the Transparent Remote File System (TRFS) proto-
col. The TRFS protocol uses special Ethernet type packets and works within a local network.
isibootd is a simple TRFS server that only supports client reads for booting and exports files in a specified directory. isibootd accepts
requests only from clients listed in the /etc/ethers and have valid hostnames.
The options are as follows:
-d tracelevel
Run isibootd in debug mode with specified tracelevel. The tracelevel can be value 1, 2, or 3, and greater tracelevel provides
more detailed trace output. The server will not fork in the debug mode.
-i interface
Specify a network interface to service network boot. If not specified isibootd searches available network interfaces (excluding
loopback) and use the first configured ``up'' one.
-s directory
Specify a directory containing boot files to be served by isibootd. If not specified isibootd uses /tftpboot by default.
FILES
/etc/ethers
/etc/hosts
/tftpboot
/var/run/isibootd.pid
SEE ALSO
ethers(5), hosts(5), tftpd(8)
http://www.NetBSD.org/ports/luna68k/install.html
HISTORY
isibootd is based on isiboot utility which was originally written by Tohru Nishimura for NetBSD/luna68k development, and first appeared in
NetBSD 6.0.
BSD
December 15, 2011 BSD