06-30-2008
I forgot earlier, but I checked the /etc/bootparams file and the files under /etc/tftpboot too.
Jeff
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I would like to upgrade the memory in my Sun Blade 150 workstation. In reading through Sun's Blade 150 DIMM Installation Guide, it indicates that the memory must be "certified by Sun for the Sun Blade 150 system."
Does anyone know if any SDRAM, PC133 • CL=2 • Unbuffered • ECC • 133MHz • 3.3V ... (2 Replies)
Discussion started by: here2learn
2 Replies
2. UNIX for Dummies Questions & Answers
Hi, I am new to UNIX. I have a Sun Blade 150 worksation. I used a Dell monitor and Dell keyboard as input and output devices. However, workstation always told me that keyboard couldn't be found. I used Dell keyboard with USB and Dell keyboard with series connector. It all didn't work. Please help... (10 Replies)
Discussion started by: duke0001
10 Replies
3. Solaris
I'm not familiar with this particular machine and it's baffling me. For those that are familar with the workstation, allow me to paint a picture. If you were looking down on the machine (open) you would see the main board and then a riser board. On the left side of the riser board are jacks... (1 Reply)
Discussion started by: silversaleen68
1 Replies
4. Solaris
Hi,
I have a Solaris 8.0 BLADE 150 machine. I have an onboard graphics alongwith an addon XVR500 graphics card. Now, when I use the motherboard graphics, I am not able to login to the XWINDOWS terminal, instead it stays on the console.
But, if I insert the monitor cable to the XVR500 port,... (2 Replies)
Discussion started by: angshuman_ag
2 Replies
5. Solaris
I have recently re-installed Solaris 10 on a Sun Blade 150 followed by a patch set (10_Recommended) dated 2011.12.05.
I have just noticed /bin/sun now returns false, rather than true. See below.
$ uname -a
SunOS myblade1 5.10 Generic_147440-07 sun4u sparc SUNW,Sun-Blade-100
$ /bin/sparc &&... (1 Reply)
Discussion started by: apmcd47
1 Replies
6. Solaris
Hi everyone
can someone please explain to me how to install solaris 10 on a sunblade 1500 using cdrom?
Thanks for your assistance (1 Reply)
Discussion started by: cjashu
1 Replies
7. Solaris
Hello,
Ive just aquired a blade 150 off ebay.Im new to suns and are having a problem getting it to boot off the cdrom.Openboot continuously tries to do a network boot and I cant enter any commands.Im using an average pc keyboard and it definetly works.Thanks for any help.:wall: (3 Replies)
Discussion started by: chucky
3 Replies
8. Solaris
Hello,
I cant get my blade box to boot off the harddrive after installing solaris 10.I can get to a root prompt after issuing "boot cdrom -s".I tried booting off disk0 and disk1,but I get "the file just loaded does not seem to be executable".Thanks for any help.:wall: (4 Replies)
Discussion started by: chucky
4 Replies
9. Solaris
Hi everybody,
I'm having big troubles in installing Solaris 8 on a Sun Blade 150.
Here are some system specs:
Sun Blade 150 (UltraSPARC-IIe 550MHz)
RAM: 256MB
OBP 4.10.6 2003/06/06 12:30
POST 2.0.1 2001/08/23 17:13
When I try to boot from Solaris 8 CD with boot cdrom or... (10 Replies)
Discussion started by: Vortigern
10 Replies
10. Solaris
hello
i have a forte gamma camera Philips device . and its a medical device. this medical device is came with sun blade 150 pc and pegasys is printed on the sun blade pc .the problem is when i switched the power on , the sun blade runs and a white screen appear with the information about the... (6 Replies)
Discussion started by: moh_abaloo
6 Replies
RARPD(8) System Manager's Manual RARPD(8)
NAME
rarpd - reverse address resolution protocol daemon
SYNOPSIS
rarpd [-d]
DESCRIPTION
Rarpd listens on the ethernet for broadcast packets asking for reverse address resolution. These packets are sent by hosts at boot time to
find out their IP address. Rarpd looks up the six octet ethernet number in the /etc/ethers file finding a host name. This name is trans-
lated to the IP address of the host by a DNS lookup. The IP address is then sent to the host.
Before rarpd can start its service it first finds out what the IP addresses of the ethernets are. It will look through /etc/ethers to map
the ethernet addresses to host names. It then uses /etc/hosts to map the host names to IP addresses. If this lookup fails then several
RARP requests are broadcasted in the hope that some RARP server knows the addresses. The IP addresses are eventually set in the same way
as ifconfig(8). (The address is not changed if already set with ifconfig.) Note that the host names in the ethers and hosts files must
match exactly. The DNS can not be used yet, so a simple name can't be translated to a fully qualified name.
Rarpd exits after startup if there are no active ethernets, or if there is no ethers file.
Warning! Sun diskless workstations assume that the first RARP server that answers is the host they are to boot from. For this to work all
other Sun RARP servers delay their answer if they are not also the requestors boot server. The Minix rarpd does not have this kludge so it
will happily engage the Sun boot server to see who can answer the client first. Unless your Minix host can actually serve a Sun diskless
client, it is better not to list any more hosts in the ethers file than necessary.
OPTIONS
-d Turns on debugging messages. Debugging can also be turned on at runtime by sending signal SIGUSR1 or turned off with SIGUSR2.
SEE ALSO
ifconfig(8), ethers(5), hosts(5), set_net_default(8), boot(8), inetd(8), irdpd(8), nonamed(8).
AUTHOR
Kees J. Bot (kjb@cs.vu.nl)
RARPD(8)