06-30-2008
I forgot earlier, but I checked the /etc/bootparams file and the files under /etc/tftpboot too.
Jeff
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I would like to upgrade the memory in my Sun Blade 150 workstation. In reading through Sun's Blade 150 DIMM Installation Guide, it indicates that the memory must be "certified by Sun for the Sun Blade 150 system."
Does anyone know if any SDRAM, PC133 • CL=2 • Unbuffered • ECC • 133MHz • 3.3V ... (2 Replies)
Discussion started by: here2learn
2 Replies
2. UNIX for Dummies Questions & Answers
Hi, I am new to UNIX. I have a Sun Blade 150 worksation. I used a Dell monitor and Dell keyboard as input and output devices. However, workstation always told me that keyboard couldn't be found. I used Dell keyboard with USB and Dell keyboard with series connector. It all didn't work. Please help... (10 Replies)
Discussion started by: duke0001
10 Replies
3. Solaris
I'm not familiar with this particular machine and it's baffling me. For those that are familar with the workstation, allow me to paint a picture. If you were looking down on the machine (open) you would see the main board and then a riser board. On the left side of the riser board are jacks... (1 Reply)
Discussion started by: silversaleen68
1 Replies
4. Solaris
Hi,
I have a Solaris 8.0 BLADE 150 machine. I have an onboard graphics alongwith an addon XVR500 graphics card. Now, when I use the motherboard graphics, I am not able to login to the XWINDOWS terminal, instead it stays on the console.
But, if I insert the monitor cable to the XVR500 port,... (2 Replies)
Discussion started by: angshuman_ag
2 Replies
5. Solaris
I have recently re-installed Solaris 10 on a Sun Blade 150 followed by a patch set (10_Recommended) dated 2011.12.05.
I have just noticed /bin/sun now returns false, rather than true. See below.
$ uname -a
SunOS myblade1 5.10 Generic_147440-07 sun4u sparc SUNW,Sun-Blade-100
$ /bin/sparc &&... (1 Reply)
Discussion started by: apmcd47
1 Replies
6. Solaris
Hi everyone
can someone please explain to me how to install solaris 10 on a sunblade 1500 using cdrom?
Thanks for your assistance (1 Reply)
Discussion started by: cjashu
1 Replies
7. Solaris
Hello,
Ive just aquired a blade 150 off ebay.Im new to suns and are having a problem getting it to boot off the cdrom.Openboot continuously tries to do a network boot and I cant enter any commands.Im using an average pc keyboard and it definetly works.Thanks for any help.:wall: (3 Replies)
Discussion started by: chucky
3 Replies
8. Solaris
Hello,
I cant get my blade box to boot off the harddrive after installing solaris 10.I can get to a root prompt after issuing "boot cdrom -s".I tried booting off disk0 and disk1,but I get "the file just loaded does not seem to be executable".Thanks for any help.:wall: (4 Replies)
Discussion started by: chucky
4 Replies
9. Solaris
Hi everybody,
I'm having big troubles in installing Solaris 8 on a Sun Blade 150.
Here are some system specs:
Sun Blade 150 (UltraSPARC-IIe 550MHz)
RAM: 256MB
OBP 4.10.6 2003/06/06 12:30
POST 2.0.1 2001/08/23 17:13
When I try to boot from Solaris 8 CD with boot cdrom or... (10 Replies)
Discussion started by: Vortigern
10 Replies
10. Solaris
hello
i have a forte gamma camera Philips device . and its a medical device. this medical device is came with sun blade 150 pc and pegasys is printed on the sun blade pc .the problem is when i switched the power on , the sun blade runs and a white screen appear with the information about the... (6 Replies)
Discussion started by: moh_abaloo
6 Replies
LEARN ABOUT OPENSOLARIS
hostconfig
hostconfig(1M) System Administration Commands hostconfig(1M)
NAME
hostconfig - configure a system's host parameters
SYNOPSIS
/usr/sbin/hostconfig -p protocol [-d] [ -h] [-n] [-v]
[-i interface] [-f hostname]
DESCRIPTION
The hostconfig program uses a network protocol to acquire a machine's host parameters and set these parameters on the system.
The program selects which protocol to use based on the argument to the required -p flag. Different protocols may set different host param-
eters. Currently, only one protocol (bootparams) is defined.
OPTIONS
The following options are supported:
-d Enable debug output.
-f hostname Run the protocol as if this machine were named hostname.
-h Echo the received hostname to stdout, rather than setting hostname using the system name directly.
-i interface Use only the named network interface to run the protocol.
-n Run the network protocol, but do not set the acquired parameters into the system.
-p protocol Run hostconfig using protocol. Currently, only one protocol (bootparams) is available. This option is required.
Specifying the -p bootparams option uses the whoami call of the RPC bootparams protocol. This sets the system's hostname,
domainname, and default IP router parameters.
-v Enable verbose output.
EXAMPLES
Example 1 Configuring Host Parameters with Verbose Output
The following command configures a machine's host parameters using the whoami call of the RPC bootparams protocol with a verbose output.
example# hostconfig -p bootparams -v
Example 2 Displaying Host Parameters
The following command displays the parameters that would be set using the whoami call of the RPC bootparams protocol.
example# hostconfig -p bootparams -n -v
Example 3 Configuring Host Parameters Less the System Name
The following command configures a machine's host parameters, less the system name, using the whoami call of the RPC bootparams protocol.
example# hostconfig='hostconfig -p bootparams -h'
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcsu |
+-----------------------------+-----------------------------+
SEE ALSO
hostname(1), domainname(1M), route(1M), attributes(5)
SunOS 5.11 6 Nov 2000 hostconfig(1M)