06-28-2008
hmmm... are you sure your route is set right?
Smiling Dragon is correct on the point that you do not see your gateway in the traceroute, however since the servers are on the same subnet you might not. What you SHOULD see is that the first or second hop is the target.
issue the command "route" and take a look at the "default" line.
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Changed from a broken Switch to a working HUB everyting else in my network is ok after the change but not my RS/6000! It refuses to get connected, get time out on Pings both ways - strange?
Could it be some problem with ARP?:confused: (2 Replies)
Discussion started by: jolun
2 Replies
2. Solaris
Hi All,
This is regarding problem with two servers...
EX:- server1(HP) is not able to connect with proxy server server2(SUN BOX)
But we can able to login.... server1 is not able to pickup any data from the proxy server...
checked in the sunbox...
# ping bdhp5050
server1 is alive
... (1 Reply)
Discussion started by: jeelans
1 Replies
3. SCO
Hi,
I have problems with my SCO unix network interfaces.
Intel integrated adapter was failing, so I installed new one - 3COM adapter into free PCI slot.
Installed driver using SCO Software manager - successfully
Added new Network adapter using SCO Network configuration manager - successfully... (0 Replies)
Discussion started by: vilius
0 Replies
4. AIX
I have AIX 5.3 OS. After issuing the print command, the printer state immediately goes down. I have checked the /etc/qconfig flle, resatrted the qdaemon but again same problem is occuring. I am using HP 5100 connected to jetdirect.
what is the problem and it's solution? (4 Replies)
Discussion started by: prashantchavan
4 Replies
5. Solaris
Hi everybody,
I have a very strange problem ; if somebody could help me it would be very kind. I'll try to explain my problem.
I have 2 unix machines absolutely identical running solaris 9.
For network reasons I need to change the IP address of the 2 machines.
I proceed exactly the same on the... (11 Replies)
Discussion started by: aribault
11 Replies
6. AIX
Dear ALL.
I installed AIX OS on customer sites.
but Only one site is too slow when I connected telnet, ftp..
Ping is too fast. but telnet and FTP is not connected..
of course i check the configuration file on aix but it's normal.
Do any Idea??
thanks in advance.
- Jun - (3 Replies)
Discussion started by: Jeon Jun Seok
3 Replies
7. Solaris
Hi
i have replace a NIC card on solaris 10 when i give the following command
ifconfig -a
it just show the lo0 (only loop back with inet 127.0.0.1)
when i give the following command to config the interface,
ifconfig elxl0 plumb
ifconfig: plumb: elxl0: no such interface
please help... (11 Replies)
Discussion started by: malikshahid85
11 Replies
8. AIX
Hi everbody;
I have 2 p520 machines and created a vio server for each one (vio01 - vio02). I created 3 AIX 5.3 lpars on vio02 and 3 AIX 6.1 lpars on vio01. The problem is when 2 lpars are activated, i can ping gateway from both lpars and vio; but when i activate 3rd lpar, network downs and none of... (2 Replies)
Discussion started by: lordofdarkness
2 Replies
9. Debian
Hello
i am configuring a debian lenny sever ,/etc/network/interfaces is modified so that eth1 takes a static IP address
then i save it wq!
then i restart the networking , /etc/init.d/networking restart .
but after reboot ,the file is reset ,note that the interfaces had by defauklt IPv6 address... (5 Replies)
Discussion started by: learn82
5 Replies
10. Android
Good day, everybody! I have a mobile phone (LG Optimus L5) with Android 4.0.3 and a tablet (PocketBook SurfPad 2) with Android 4.1.1 and I have problem with wireless network on these devices. Laptops don't have such problem. My wireless network organisation is a modem connected with an access point... (11 Replies)
Discussion started by: qzxcvbnm
11 Replies
LEARN ABOUT DEBIAN
traceroute
TRACEROUTE(1) User Commands TRACEROUTE(1)
NAME
traceroute - Trace the route to a host
SYNOPSIS
traceroute [OPTION...] HOST
DESCRIPTION
Print the route packets trace to network host.
-f, --first-hop=NUM
Set initial hop distance, that is the time-to-live.
-g, --gateways=GATES
List of gateways for loose source routing.
-I, --icmp
Use ICMP ECHO as probe.
-m, --max-hop=NUM
Set maximal hop count (default is 64).
-M, --type=METHOD
Use METHOD (icmp or udp) for traceroute operations, defaulting to udp.
-p, --port=PORT
Use destination PORT port (default is 33434).
-q, --tries=NUM
Send NUM probe packets per hop (default is 3).
--resolve-hostnames
Resolve hostnames.
-t, --tos=NUM
Set type of service (TOS) to NUM.
-w, --wait=NUM
Wait NUM seconds for response (default is 3).
-?, --help
Give this help list.
--usage
Give a short usage message.
-V, --version
Print program version.
GNU inetutils 2015-05-15 TRACEROUTE(1)