Sponsored Content
Full Discussion: Solaris zone routing table
Operating Systems Solaris Solaris zone routing table Post 302209367 by seg on Thursday 26th of June 2008 05:02:21 PM
Old 06-26-2008
If is "keeps coming back" you might have the wrong netmask(s) in /etc/inet/netmask
 

9 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

not following routing table

Hi, I'm trying to connect to a network device, with the connection follwoing the UNIX routing table we set up. Its to go via a specific network Gateway and out throught a specific Lan card (Lan4). However when trying to conenct it keeps going through Lan3 and will not get to its destination.... (3 Replies)
Discussion started by: nhatch
3 Replies

2. IP Networking

Ip routing table

hi all, how to access ip routing table throgh program, how should i integrate my rip routing table with the ip routing table :) (0 Replies)
Discussion started by: vinodkumar
0 Replies

3. IP Networking

routing table

hi all... i need to know, where is locate the routing table on sun solaris, how i can saved the configuration.... because when i restart the server, lost the configuration.... thank you... Regards... (3 Replies)
Discussion started by: chanfle
3 Replies

4. IP Networking

Routing table

Hi all, I am confusing with routing table, i use linux and iptables. i have 1 internet gateway, and 1 router for VPN. here is my network. eth0=192.168.0.1 eth1=192.168.100.1 192.168.0.0/24 --- eth0(Linux Box)eth1 ---(DSL)---Internet | ... (4 Replies)
Discussion started by: blesets
4 Replies

5. Linux

Routing Table

Hello, how to make entries in routing table perminent (1 Reply)
Discussion started by: teenasuresh
1 Replies

6. Solaris

how do i make a route entry permanent in the routing table on solaris 8?

how do I make sure that the entry in the routing table on Solaris 8 stay permanent after rebooting the server. For example route add 172.20.1.60 -netmask 255.255.255.0 172.20.255.253 Each time the server reboots the entry disappears when using the command netstat -nr (2 Replies)
Discussion started by: tv.praveenkumar
2 Replies

7. UNIX for Advanced & Expert Users

Solaris 10 routing table issues

Hello Hope someone can help with this problem. We are running Solaris 10 with a current kernel patch of 142900-09. We appear to be getting a serious issue with the routing table as shown below: Output from netstat -rnv Destination ....Mask ............Gateway ........Device... (2 Replies)
Discussion started by: gregsih
2 Replies

8. HP-UX

how to read routing table

Hi all, Could someone please explain to me how I should read this routing table, # netstat -rn Routing tables Destination Gateway Flags Refs Interface Pmtu 127.0.0.1 127.0.0.1 UH 0 lo0 32808 10.222.47.82 10.222.47.82 UH... (3 Replies)
Discussion started by: rachael
3 Replies

9. Solaris

Solaris 11 Global zone patching having Solaris 10 branded zone

I am planning to do solaris 11 global zone patching having solaris 10 branded zone. I have a doubts on step 8 specially Can someone clear my step 8 doubts or if anything wrong between step 1 to step 9 please correct that also as I have pretty good idea about Step 10 mean patching in solaris 10... (2 Replies)
Discussion started by: amity
2 Replies
VDE_L3(1)						      General Commands Manual							 VDE_L3(1)

NAME
vde_l3 - Virtual Distributed Ethernet 'Layer 3' Switch. SYNOPSIS
vde_l3 -v vde_plug:ipaddress/netmask [-v...] [-r target_network/netmask:gateway] [-G default_gw] [-M mgmt_socket] DESCRIPTION
A vde_l3 connects to one or more vde_switches, performing ip forwarding among its virtual interfaces. A new interface is created at startup for each -v option given at command line. Static routes to target networks can be defined using the -r option. vde_l3 -v /var/run/s1.ctl:192.168.0.1/24 connects to the vde sock at /var/run/s1.ctl with its virtual interface ve0, having the address 192.168.0.1 and netmask 255.255.255.0. vde_l3 -v /var/run/s1.ctl:192.168.0.1/24 -v /var/run/s2.ctl:10.0.0.254/255.255.0.0 connects to the two vde socks, with its virtual interfaces ve0 and ve1, having addressess 192.168.1.0 and 10.0.0.254 respectively. Hosts in each network can specify the vde_l3 as their gateway to reach the other one. OPTIONS
-v vde_plug:ipaddress/netmask Creates a virtual network interfaces on the vde_l3 box, with address ipaddress and netmask netmask. Please note that the netmask can be specified either in the 'classic' A.B.C.D mode, or just by giving the number of leading bits (f.e., /17 for 255.255.128.0). One can define as many interfaces as she wants. -r target_network/netmask:gateway Specify a static route through gateway to reach hosts in target_network with netmask netmask. One can define as many routes as she wants. -G default_gw Specify a default gateway, to be used whenever no static route is defined for a target host. -M mgmt_socket the unix socket where the parameters (interfaces addresses, routes, etc.) can be checked and changed runtime. unixterm(1) can be used as a remote terminal for wirefilter. NOTICE
Virtual Distributed Ethernet is not related in any way with www.vde.com ("Verband der Elektrotechnik, Elektronik und Informationstechnik" i.e. the German "Association for Electrical, Electronic & Information Technologies"). SEE ALSO
vde_switch(1), vdeq(1), unixterm(1), vde_cryptcab(1), wirefilter(1). AUTHORS
VDE_L3 is a tool by Daniele Lacamera <root@danielinux.net> VDE is a project by Renzo Davoli <renzo@cs.unibo.it> Virtual Distributed Ethernet May 7, 2007 VDE_L3(1)
All times are GMT -4. The time now is 06:46 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy