break solaris mirror Post: 302208703

9 More Discussions You Might Find Interesting

1. Solaris

Mirror solaris

Hi everyone. I have a Sun Solaris box which is running on only one internal disk and obviously that is not a good thing, if the disk should fail. This is a pritty straight forward operation in AIX, where my experties are. I have never done this in solaris and would therefore appriciate any help...

2. Solaris

Disk Mirror in Solaris 9 via Solaris Volume Manager

Hello, I am trying to do mirror in solaris 9. I have total 0-7 disks 4 5 6 7 0 1 2 3 Drive 0 and Drive 4 = Boot Drives Need to Mirror following drives. Drive 1 and Drive 5 = Need to mirror Drive 1 was mounted on: /prod1, /prod2, /prod3, /prod4, /prod5. Then i...

3. HP-UX

Break mirror so that it can be used later

Hello again, We need to install patches to HP-UX B.11.11 but would like to break the mirror it has (with out damaging it) so that in case of failure we can use this a meassure procedure. Any ideas on how to do this Thank you!

4. Solaris

patch update and break mirror

Hi All, How do you know if you need to break the mirror on solaris 8 patch update? Here's the patch example, 117350-54. On the site, it's just a low type update and not a medium or critical. Is breaking a mirror a best practice only or really a requirement to some patch? Thanks, itik

5. Solaris

Solaris Volume Manager: Break Mirror and use to make a 2nd machine

Hello: I have a machine built on 2 drives and mirrors have been created to a second set of 2 drives (4 total) on the same platform. SVM. Might anyone provide guidance to create a second machine by breaking the mirrored set, moving the two mirrors (2) to another machine (same platform type),...

6. Linux

LVM - break mirror taking out orignal copy

Hi Guys, I have a mirrored LVM volume, and wish to break the mirror leaving only copy1 (effectively removing copy 0). Here's the config: # lvs -a -o +devices lvdata vg01 mwi-ao 2.19T lvdata_mlog 100.00 lvdata_mimage_0(0),lvdata_mimage_1(0) vg01...

7. Solaris

Solaris patching using mirror disk backup? need help!

hi friends, need help.. it is my first time patching using mirror disk backup approach, not so sure about the steps :confused: how do you detach, patch it, boot it and reattach it ? any kind soul here can advise ? thanks in advance..:) below is the information from my machine: Filesystem ...

8. Solaris

Healthy mirror on Solaris 10

Dear All I have question and I want some one to answer it .. in Solaris 10 I have two mirrors as below .. c3t0d0s0 & c3t1d0s0 NAME STATE READ WRITE CKSUM rpool ONLINE 0 0 0 mirror-0 ONLINE 0 0 0 ...

9. AIX

AIX break rootvg mirror from system down

Hello, aix 5.2, mirrored rootvg on hdisk0 and hdisk1. hdisk0 is dead. I can boot to cd, into sms, into maintenance mode. I can fsck all the various partitions on hdisk1 (the hd4 hd2 hd3, etc...) all is fine. But without the hdisk0 part of the mirror I cannot get the system to boot. ystem hangs on...

LEARN ABOUT DEBIAN

jigdo-mirror

JIGDO-MIRROR(1) 														   JIGDO-MIRROR(1)

NAME

       jigdo-mirror - Maintain a mirror of images offered with jigdo

SYNOPSIS

       jigdo-mirror [ config-file ]

DESCRIPTION

       See jigdo-file(1) for an introduction to Jigsaw Download.

       jigdo-mirror  is a script intended for people who want to offer direct HTTP or FTP downloads of files for which only the jigdo and template
       files are available.

       As the first step of using jigdo-mirror, you need to set up normal HTTP/FTP/rsync mirroring both of the `.jigdo'/`.template' files  and	of
       the  parts  that  are  needed  for the reconstruction of the images. For example, in the case that you want to mirror Debian CD images with
       jigdo-mirror, you need a mirror of the `.jigdo'/`.template' files and a Debian mirror on the local machine.

       At regular intervals (preferably immediately after the normal mirroring has finished), schedule a  run  of  jigdo-mirror.  It  will  search
       through a given directory for any `.jigdo' files and attempt to create all images offered by each file.

       The  script  requires  you  to  set a number of variables - please refer to the start of /usr/bin/jigdo-mirror for a description of each of
       them. Since /usr/bin/jigdo-mirror will be overwritten whenever you upgrade jigdo-mirror, it is highly recommended not to  change  the  set-
       tings  directly	in  this script. Instead, personal settings should be saved in a file called .jigdo-mirror in your home directory, or in a
       different file whose name is then passed to the script as its first (and only) command line argument.

SEE ALSO

       jigdo-file(1), jigdo-lite(1)

       CD images for Debian Linux can be downloaded with jigdo <URL:http://www.debian.org/CD/jigdo-cd/>.

AUTHOR

       Jigsaw Download <URL:http://atterer.net/jigdo/> was written by Richard Atterer <jigdo atterer.net>, to make downloading of  CD  ROM  images
       for the Debian Linux distribution more convenient.

								    19 May 2006 						   JIGDO-MIRROR(1)