06-24-2008
break solaris mirror
Hi All,
How do I break the solaris 8 mirror? And how do I make sure I will point the first hd mirror on reboot.
If the first break mirror won't boot. How do I make the copy mirror to boot?
Thanks in advance,
itik
9 More Discussions You Might Find Interesting
1. Solaris
Hi everyone.
I have a Sun Solaris box which is running on only one internal disk and obviously that is not a good thing, if the disk should fail. This is a pritty straight forward operation in AIX, where my experties are. I have never done this in solaris and would therefore appriciate any help... (3 Replies)
Discussion started by: sprellari
3 Replies
2. Solaris
Hello,
I am trying to do mirror in solaris 9. I have total 0-7 disks
4 5 6 7
0 1 2 3
Drive 0 and Drive 4 = Boot Drives
Need to Mirror following drives.
Drive 1 and Drive 5 = Need to mirror
Drive 1 was mounted on: /prod1, /prod2, /prod3, /prod4, /prod5.
Then i... (3 Replies)
Discussion started by: deal732
3 Replies
3. HP-UX
Hello again,
We need to install patches to HP-UX B.11.11 but would like to break the mirror it has (with out damaging it) so that in case of failure we can use this a meassure procedure.
Any ideas on how to do this
Thank you! (2 Replies)
Discussion started by: AQG
2 Replies
4. Solaris
Hi All,
How do you know if you need to break the mirror on solaris 8 patch update?
Here's the patch example, 117350-54. On the site, it's just a low type update and not a medium or critical.
Is breaking a mirror a best practice only or really a requirement to some patch?
Thanks,
itik (1 Reply)
Discussion started by: itik
1 Replies
5. Solaris
Hello:
I have a machine built on 2 drives and mirrors have been created to a second set of 2 drives (4 total) on the same platform. SVM.
Might anyone provide guidance to create a second machine by breaking the mirrored set, moving the two mirrors (2) to another machine (same platform type),... (1 Reply)
Discussion started by: 4dailyrunner
1 Replies
6. Linux
Hi Guys,
I have a mirrored LVM volume, and wish to break the mirror leaving only copy1 (effectively removing copy 0).
Here's the config:
# lvs -a -o +devices
lvdata vg01 mwi-ao 2.19T lvdata_mlog 100.00 lvdata_mimage_0(0),lvdata_mimage_1(0)
vg01... (0 Replies)
Discussion started by: badoshi
0 Replies
7. Solaris
hi friends, need help.. it is my first time patching using mirror disk backup approach, not so sure about the steps :confused: how do you detach, patch it, boot it and reattach it ? any kind soul here can advise ? thanks in advance..:)
below is the information from my machine:
Filesystem ... (3 Replies)
Discussion started by: Exposure
3 Replies
8. Solaris
Dear All
I have question and I want some one to answer it ..
in Solaris 10 I have two mirrors as below .. c3t0d0s0 & c3t1d0s0
NAME STATE READ WRITE CKSUM
rpool ONLINE 0 0 0
mirror-0 ONLINE 0 0 0
... (1 Reply)
Discussion started by: top.level
1 Replies
9. AIX
Hello,
aix 5.2, mirrored rootvg on hdisk0 and hdisk1. hdisk0 is dead. I can boot to cd, into sms, into maintenance mode. I can fsck all the various partitions on hdisk1 (the hd4 hd2 hd3, etc...) all is fine. But without the hdisk0 part of the mirror I cannot get the system to boot. ystem hangs on... (6 Replies)
Discussion started by: sshapiro
6 Replies
LEARN ABOUT DEBIAN
pull-debian-source
PULL-DEBIAN-SOURCE(1) General Commands Manual PULL-DEBIAN-SOURCE(1)
NAME
pull-debian-source - download and extract a source package from Debian
SYNOPSIS
pull-debian-source [options] <source package> [release|version]
DESCRIPTION
pull-debian-source downloads and extracts the specified version of source package, or the latest version in the specified Debian release.
pull-debian-source will try the preferred mirror, default mirror, security mirror, and fall back to Launchpad or snapshot.debian.org, in
search of the requested version.
OPTIONS
source package
The source package to download from Debian.
release
The release to download the source package from. Defaults to unstable.
version
The specific version of the package to download.
-d, --download-only
Do not extract the source package.
-m DEBIAN_MIRROR, --mirror=DEBIAN_MIRROR
Use the specified mirror. Should be in the form http://ftp.debian.org/debian. If the package isn't found on this mirror,
pull-debian-source will fall back to the default mirror.
-s DEBSEC_MIRROR, --security-mirror=DEBSEC_MIRROR
Use the specified mirror. Should be in the form http://security.debian.org. If the package isn't found on this mirror,
pull-debian-source will fall back to the default mirror.
--no-conf
Do not read any configuration files, or configuration from environment variables.
-h, --help
Display the usage instructions and exit.
ENVIRONMENT
All of the CONFIGURATION VARIABLES below are also supported as environment variables. Variables in the environment take precedence to
those in configuration files.
CONFIGURATION VARIABLES
The following variables can be set in the environment or in ubuntu-dev-tools(5) configuration files. In each case, the script-specific
variable takes precedence over the package-wide variable.
PULL_DEBIAN_SOURCE_DEBIAN_MIRROR, UBUNTUTOOLS_DEBIAN_MIRROR
The default value for --mirror.
PULL_DEBIAN_SOURCE_DEBSEC_MIRROR, UBUNTUTOOLS_DEBSEC_MIRROR
The default value for --security-mirror.
SEE ALSO
dget(1), pull-debian-debdiff(1), pull-lp-source(1), ubuntu-dev-tools(5)
ubuntu-dev-tools 22 January 2011 PULL-DEBIAN-SOURCE(1)