06-12-2008
A good place to start looking would be the routing table. Issue a "netstat -r" and have a look t the routing rules. Probably the interface connecting to the internet is set as default route.
To switch off IPng use SMIT to change the properties of the IP stack.
bakunin
9 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
hello
i'm working on aix 5300-05-03 hacmp ver 5.4
well my issue is that when firewall (gateway to internet ) goes down my machine start to work very very slowly!!!
the output of the sniffer is that on the output card , my machine try to convert ipv4 to ipv6 0.0.2.0
my machine is not configure... (1 Reply)
Discussion started by: ariec
1 Replies
2. IP Networking
Need help...!
I want to configure Samba 3 for IPv6 operation with Window XP for IPv4.
I appreciate any guide.
Thanks
HSV (0 Replies)
Discussion started by: Sovan
0 Replies
3. Solaris
Hi folks, i hope you'll help me to configure my ipv6 tunnel.
First, i create my tunnel in:
Hurricane Electric Free IPv6 Tunnel Broker
My IP is 83.228.93.34
in HE:
------------------------
Server IPv4 address: 216.66.84.46
Server IPv6 address: 2001:470:1f14:16a::1/64
Client IPv4 address: ... (2 Replies)
Discussion started by: static
2 Replies
4. Shell Programming and Scripting
I have perl script that I use to check and ping a list of ip,
The problem is, I didnt understand how to ping ipv6 on perl,
Could I use Ping::External??And how could I get the ping result (reply or not)?
This is my code
#!/usr/bin/perl --
use Net::Ping;
use Data::Validate::IP;
use... (3 Replies)
Discussion started by: franzramadhan
3 Replies
5. Red Hat
Hello,
I was wondering if it would be possible to run two VMs one with services for IPv4 and the other one with services for IPv6. The main physical system would be connected to a IPv6 switch.
I think it should be fine but I would like to hear out your comments. (1 Reply)
Discussion started by: svalenciatech
1 Replies
6. Solaris
Hi
I am looking to set-up ISC DHCP to support ipv6, and to migrate my existing SUN DHCP ipv4 to ISC,
finding the ipv4 options for the SUN DHCP options was ok eg
TFTPsrvN = tftp-server-name
OptBootF = bootfile-name
However if I set up a DHCPv6 does anyone know what the equivalent... (1 Reply)
Discussion started by: eeisken
1 Replies
7. AIX
Hi all,
I have setup ipv6 in AIX machine using autoconf6 command.
I was successfull in doing this. after execution of the command local link address was assigned to one of the interfaces
(en1).But I have to setup the following environment as well.
1) Machine with only IPv6 support(IPv4... (0 Replies)
Discussion started by: ard
0 Replies
8. Solaris
Hi,
I am looking for a solution to configure ntp between ipv4 ( ntp server ) to ipv6 ( client) .
I had google, but lot many sites suggest to have dual stock or tunnaling.
my issue is I have client has only ipv6 address ans server has ipv4 address. is it possible to sync time,... (4 Replies)
Discussion started by: naveen.surisett
4 Replies
9. Solaris
Hello dears
how to assign IPv4 and IPv6 addresses with same interface on solaris 10 (1 Reply)
Discussion started by: ttashman
1 Replies
LEARN ABOUT MINIX
tc-route
Route classifier in tc(8) Linux Route classifier in tc(8)
NAME
route - route traffic control filter
SYNOPSIS
tc filter ... route [ from REALM | fromif TAG ] [ to REALM ] [ classid CLASSID ] [ action ACTION_SPEC ]
DESCRIPTION
Match packets based on routing table entries. This filter centers around the possibility to assign a realm to routing table entries. For
any packet to be classified by this filter, a routing table lookup is performed and the returned realm is used to decide on whether the
packet is a match or not.
OPTIONS
action ACTION_SPEC
Apply an action from the generic actions framework on matching packets.
classid CLASSID
Push matching packets into the class identified by CLASSID.
from REALM
fromif TAG
Perform source route lookups. TAG is the name of an interface which must be present on the system at the time of tc invocation.
to REALM
Match if normal (i.e., destination) routing returns the given REALM.
EXAMPLES
Consider the subnet 192.168.2.0/24 being attached to eth0:
ip route add 192.168.2.0/24 dev eth0 realm 2
The following route filter will then match packets from that subnet:
tc filter add ... route from 2 classid 1:2
and pass packets on to class 1:2.
NOTES
Due to implementation details, realm values must be in a range from 0 to 255, inclusive. Alternatively, a verbose name defined in
/etc/iproute2/rt_realms may be given instead.
SEE ALSO
tc(8), ip-route(8)
iproute2 21 Oct 2015 Route classifier in tc(8)