Fibre channel drivers on RS/6000 aix 5L Post: 302203568

9 More Discussions You Might Find Interesting

1. AIX

Install Fibre Card AIX 5.3

Hello, I have two systems that are being prepared to be SAN attached .. can anyone tell me any specific checks I should perform prior to the cards being installed... I am aware of firmware / OS level and relevant drivers, is there anything else? thanks Chris.

2. AIX

Power6 Virtual Fibre Channel Adapter

Hello, Searched in all IBM Redbooks and on the internet and couldn't find anything about the new feature of POWER 6 which Virtual Fibre ( Fiber ) channel adapter. It is similar to virtual scsi adapter. In my client partition I created the virtual Fibre Adapter mapped it with the VIO...

3. UNIX for Advanced & Expert Users

Can AIX 5.3 - 6 Boot From HP EVA 6000 SAN

Hi There, Has anyone had any luck with or know how to get AIX 5+ to boot from a HP EVA 6000 SAN? The servers used here will be P Class Blades My initial searches on this so far did not bring results so I am guessing this may not be possible on HP SAN's but please let me know if I am...

4. Solaris

USCSICMD ioctl calls for Fibre Channel(FC) devices on Solaris 10?

Hi , I have wrtitten a C program that issues USCSICMD ioctl call to the tape devices attached on solaris sparc 10. I was able to get the required information from all SCSI tape devices attached using the utility. But, whenever it is run on FC attached tape drives , the program returns an error...

5. Hardware

Fibre Channel HBA recommendations?

We will be buying new Xeon E5-based servers for our datacenter and were wondering which Fibre Channel host bus adapters we should select for these. The choices are Emulex or QLogic (8Gb FC HBAs). Anybody have any recommendations on which is the better choice? Thanks in advance.

6. AIX

AIX - Fibre Adapter and IBM Storage

Hello, Just a quick question Usually from a PSERIES if you want to connect to IBM SAN Storage you connect the IBM SAN Storage through a SAN Switch something like this --- however my question Can you connect from Pseries directly to San Storage without SAN Switch what would be...

7. Solaris

Fibre channel link down on booting Solaris server

Hi I had power issue that affected a server, in which I had power ON the server SPARC T1-B3 running solaris 10. After power on the system stops at ok prompt, them I issued the following commands: {0} ok setenv auto-boot? false auto-boot? = false {0} ok reset-all SPARC T3-1B,...

8. AIX

[ASK] - AIX Fibre Channel behavior

Hello all, Let me introduce about the context and my environment. We have an AIX 6.1 system, it has 4 FC channels / > lsdev -Cc adapter | grep fcs fcs0 Available 23-T1 Virtual Fibre Channel Client Adapter fcs1 Available 23-T1 Virtual Fibre Channel Client Adapter fcs2 Available 23-T1...

9. Solaris

Fibre Channel link not ready on Netra 240

Hi, One of my Netra 240 went into hung state and I had to reboot it. I powered it off and tried booting it again but unsuccessful. It is not connected to SAN and have local disks. Not able to boot in failsafe mode too. There are two disks of 72GB, both are mirrored in SVM. It complains about...

LEARN ABOUT NETBSD

ipwctl

IPWCTL(8)						    BSD System Manager's Manual 						 IPWCTL(8)

NAME

     ipwctl -- configure Intel PRO/Wireless 2100 network adapter

SYNOPSIS

     ipwctl [-i] iface
     ipwctl [-i] iface -r

DESCRIPTION

     The ipwctl utility controls the operation of Intel PRO/Wireless 2100 networking devices via ipw(4) driver.

     You should not use this program to configure IEEE 802.11 parameters.  Use ifconfig(8) instead.

OPTIONS

     The options are as follows:

     -i iface
	     Display adapter's internal statistics.

     -i iface -r
	     Display the radio switch state (on or off).

FILES

     The firmware, loaded automatically, is not shipped with NetBSD; install the pkgsrc/sysutils/ipw-firmware package.	The original archive is
     available from Intel at: http://ipw2100.sourceforge.net/firmware.php?fid=3.

     ipw2100-1.2.fw    BSS mode (connection to an access point) firmware
     ipw2100-1.2-i.fw  IBSS mode (point-to-point connection) firmware
     ipw2100-1.2-p.fw  Monitor mode firmware

SEE ALSO

     ipw(4), ifconfig(8), pkgsrc/sysutils/ipw-firmware

AUTHORS

     The ipwctl utility and this man page were written by Damien Bergamini <damien.bergamini@free.fr>.

BSD
								  April 17, 2006							       BSD